Search results

Thanks, I've been looking at the BB6 ones as they tilt etc. Cars is just for road. Ideally would rather have trendlines but they a few more £££s.

Hi. Just wondering if anyone has fitted BB Classics BB6 seats in their 1*2 and if yes, what are they like. Thanks in advance

My old one did this. To release mine I had to pull the bonnet sideways first then up. The catch had corroded and was all jammed up whilst the bonnet latch was being pulled.

will have a look. thanks steve

Hi. I've had a look through the forum but only found partial solutions/advice. So here goes and apologies or the length. Saturday morning 182 wouldn't start. door locks sounded sluggish and just single clicked when trying to start. thought battery so put it on charge. this at least let it lock...

Brother in law has put the 2zz engine in his mr2. Trying to persuade him to track it. Think we’re both too chicken though lol. You where flying round on satd. Was very impressed.

Yes bud. Hull.

Would have tried to say hello at csf but more of a social recluse. Mine had its longest drive since ownership (over 2 years). Only flagged an eml for pre cat on way home which has cleared. Did briefly meet clio fool and the guys in the light blue phase 1.

Mine doesn’t work so clio got left on the drive today.

Car looked good on satd. Wasn’t sure about the wheels but seeing them in person I like them. I don’t have AC delete on mine but I do apparently have a leak as it doesn’t work anyway even after replacing half the system and getting it regassed. Was 50/50 on which car to drive today but went for...

Hope the 3D parts fit. If they’re not the right ones for you car let me know and I’ll sort out sending you a different set. I only have designs for ph1 and ph2 though.

First time I’ve been to an event like today and got to say the two red mk 1 and the blue mk2 ph1 just seemed so rapid.

Couldn’t stay all day but had a good day, met some nice people and watch a few good battles on track. 👍

Hi. Does anyone know what this connector is for please? It’s tucked up behind the glove box above the passenger foot well. Cheers in advance.

Acoustic valve possibly as well.

Booked but can only attend on sat'd morning. Hopefully the shed will make it.

Sorted. 1st replacement resistor pack was duff. Tried another one and all good.

mine started working again but has since stopped again. I can hear something kind of clicking behind the dash when I switch between auto and off. Did you solve yours?

Sorted it. Sliders had jammed up. Cars been parked for quite some time. Now standing in the corner facing the wall for 10 minutes.

Hi. Help please. I’ve fitted new discs and now trying to fit the pads but they won’t fit. I’ve wound the piston back and the pad between piston and disc has loads of room. The other side. Disc to outer there isn’t enough space to get the pad in. Brake disc spacers as in. Flat to the disc...

Hi. What size bolts should be in the rear shock absorbers please? Just undone more to change the springs abs shocks but I have different size bolts on each side. One 15mm head and the other 18mm head. The thread on the 15mm one is shot so going to replace both. Does anyone have a link or can...

I’ve got a set of proper cup ones on shelf but would save them if these are any good. I’m guessing junk as other ones on eBay with same manufacturer name but not number are like £30 a pair but wanted to check.

Hi. I’ve had a look at the rear shocks on my 182 and it looks like they are called primeline SA559. I’ve never heard of them and can’t find the same ones when I googled them. They look pretty new but are they junk and should I just swap them out for proper cup ones? Replacing the rear springs so...

Might have solved it. Diy fix so will see how long it lasts and if it works properly once back in the car. Knocked the pin out of a pop rivet, slit the side with a dremel to fit over the wire then nipped it up. Did have a washer over it to stop the rivet opening back up but it pulls it too...

Hi, I've swapped the seat rails over on my drivers seat and attached the cable for making it tilt and slide. This wasn't connected when I took the seat out to sort the sliding mechanism. When I pull the handle it tilts fine but as it folds forward the cable to the runner pops out of the slot...

They’ve emailed me back and said the flange isnt supposed to be square. Can anyone confirm?

I’ve took a punt and got one from cats2u. Just arrived and the cat to manifold flange isn’t welded on square. 🤯

not sure i'd fancy swapping them in and out. taking my old cat off was a nightmare. it just would not come out of the centre section

Looks like KTEC offer 12 months now. still not great though

Hi, I've stripped the Cat off my 182 as the previous MOT said it had a leak and it was covered in exhaust paste. Anyway after an absolute night mare getting it off, I think the leak was down to 75% of the gasket missing but I think the Cat is goosed anyway. Exhaust paste on the brick inside...