Search results

Thanks for the replies chaps, seems these cracks are the cause of the exhaust blow rather than what I thought was the olive joint Sent from my iPhone using Tapatalk

Is this the one advertised on scorpion site? Think I will be doing the same next year. Just hope that it’s not too loud Sent from my iPhone using Tapatalk

Yes 192 and the cracks look very similar but not quite as bad - yet.. thanks Sent from my iPhone using Tapatalk

Been under the car this morning trying to sort my blowing exhaust (cat to centre silencer join) looking at the front face of the silencer there seems to be what looks like small stress cracks forming in the stainless steel, has anyone else had similar with stainless systems? Sent from my...

I cut some 9mm ply to size and fitted under the carpet Sent from my iPhone using Tapatalk

Having a similar issue - Did this get sorted?

Hi Mate, can't see the image google says page blocked? Yeah I have tried silicone but I think the clamp is shot. Im using the two bolt type. Think it needs removal cleaning and reassembly

Had a constant blow from the centre joint at the rear of the cat. Have got a 192 Stainless fitted and have heard these are difficult to seal properly. Could anyone advise how these can be properly sealed and clamped?

Wheelbolts tight James, I took the wheel off and unfortunatly found a few issues, 1. Trackrod end balljoint gaiter is ripped. 2. CV gaiter has been jubilee clipped on at some point in the past and now grease is leaking out of it. Boot is not ripped though. 3. Track rod inner gaiter is split...

Thanks Mr Plums Will give them a tweak and see.

Gearbox mount replaced, engine is a lot more solid now now wobbles but!!!!! still have the click click when taking up drive. Any further ideas, have tried driving in circles on full lock and no clicks from the driveshaft CV's. Suppose it could be the wishbone bushes or balljoints

The bungs were leaking on my 182, The flat boot floor allowed the water to flow forward. As above sealed them and all ok now.

As title says, i have a click click when taking up drive, I recently replaced the dog bone and the sound went but the new dog bone allowed the manifold to hit the anti roll bar and cause a horrendous noise when booting it (This was the steel plate version) . I have now changed this dog bone back...

Thanks will check Sent from my iPhone using Tapatalk

Im getting an annoying whistling sound from the ventilation system, Seems to be coming from the windscreen vents, no adjustment of the heater controls seems to make any difference however these are working as the airflow changed to the desired vent the sound persists. Could this be due to a...

Release bearing has started squealing, need this sorting and a new clutch fitting - can anyone recommended a good garage to use in the Coventry area?

Bled them today, although I could do the same before Sent from my iPhone using Tapatalk

The pedal doesn’t go to the floor when driving in the sense of normal braking however I can get the pedal to the floor / end of travel when stationary and engine running Sent from my iPhone using Tapatalk

Sitting in the car with off, pedal is firm (after using up the servo) with engine running I can press the pedal to the floor is this normal? Brakes seem to work ok. Sent from my iPhone using Tapatalk

How did you get the Renault wording on the display?

As far as the lights I think that the blanks are removed and the lights are screwed into place, wiring wise I'm not sure, you may have to install your own wiring Sent from my iPhone using Tapatalk

I'm aware that the door pull with the switches are flecked, so the door opening handle should be flecked too? Sent from my iPhone using Tapatalk

Black and silver or grey and silver, I have one of each in mine and need to know which colour is correct Sent from my iPhone using Tapatalk

I have flocked my interior door pulls, Bought the kit from Flocking and have had similar results, looked like it had covered quite well but when dry lots of the flock was not adhered and left me with a patchy finish. Not too noticeable unless you look closely but I imagine the same result of a...

Are these still available new? Mine have started to peel off. Sent from my iPhone using Tapatalk

Not had any experience of the foam splitter but have purchased and fitted the Skoda one. TBH The Skoda one is dead easy to fit, I did mine with the bumper on the car but if I was to do it again I would remove the bumper. Another thing I did was to keep the "ended" sections by the wheel arch and...

Nice one Daz, Thanks

Anyone got a PDF they could post up, Would like to know what is involved before purchasing a kit. Rich

Noticed my passenger side was knocked off after Cambelt change, its quite close to the air intake and its easy to knock when removing the pipe from the we acoustic valve.

Thanks