Search results

Is the mm2 figure of the inner strands only?

Have ordered the loom. I measured the gauge of the wire from the other plugs (red and green) but they are 3.8mm and 3.4mm which seems too small. The wire coming out the fuse holder is the thicker 4.5mm ish guage for all connections so Ill be able swap out the green plug for the brown when It arrives

Few more things done. Gave the subframe a very brief clean to get rid of all the pas fluid, although dont want to mount the rack and frame until Ive done the alternator setup, should be here soon. Column is bolted up and ready to wire, If I can ill use the oem power wiring which means just...

I just checked and the green connector is for the air conditioning fan which I dont have, so I can just replace it with that?

Ah okay! I see it here, but I dont have the extra slots by this relay so I take it Id need the full epas engine bay loom and bulkhead loom? Will just do it on its own power otherwise.

I was just looking through your thread funnily enough. But I dont understand as mine already has the red connector for the fuse?

Power and earth plug already in the loom? (loom from 172 cup) Its not connected to the battery though? @GrahamS

But this is the light you want to keep warm so it makes you look better than you really are, led so bright will make you look some hunch back of notre dam

Whats the difference, front piston size and rear sepherical rather than bushing for bolt mount?

@YorkshireKyle Youtube screwed me over on this. Plenty of the right information and plenty of the wrong information, all mixed together and hard to distinguish

Like somebody was murdered. Just today have I got things cleaned up and the subframe outside ready to clean. Cant wait for epas now.

What are everyones views on pushing the pedal all the way to the floor? The way its done or a good way to wreck the mc?

As you can see from the pictures, a huge mess and a faulty rack, some 200+ quid worth of lines not to be used again and whats to replace all that! Such a waste of time and energy but its experience doing the jobs so at least that. Also f**k not doing any of this without the makita, honestly has...

Thanks! Hopefully its how I remember

😁 😁 The wrinkle paint must be satisfying to do. Painting in general is a relief for me when It goes okay because I have no idea what im doing! Also I just realised that I have the wrong part of the loom for the abs could you sell me yours? :unsure:

it didnt :rolleyes: I knew what speed I was going via rpm and what gear

I dont really want to change my mind now lol. Abs loom back in and have ordered everything that I didnt have anymore (everything apart from the loom) o_O I know it was reliable for me when I had it and Ive absorbed enough brake fluid for more tests lol

Its the full 172 cup system mate

cup one

On ad08rs up front, before that a048. Pads are ds1.11. The pedal travel is so short when bled up there is about 5-10mm between light braking and fully locking up. The pedal then overtime has that similar short travel when the brakes engage, but it happens some 30-40mm further, so you put your...

In terms of problems Ive had to keep re bleeding the system for a while now, possible master cylinder fault or rear caliper or both. But Im just tired of having to feather the brakes more so they dont lock up, abs makes one less thing to worry about. I didnt swap out a mc because I 'knew' I was...

What are you doing instead of the tilton valve?

More the reason to get a proper ecu now! I wonder how much data could be used for the mapping of the assist, I had the idea of using yaw and cg data to make the steering assist more consistent since in a turn espeically with the bank against you, the steering would be at its heaviest. Obviously...

I wont be fitting the guage now unfortunately as the rack shat it self. I would of liked to of known the temps as well to see what sort of driving does what to the system. Im not sure with the electric pumps, I know with belt driven a company were selling adaptors that just let more or less...

lol they threw the box away as they thought it was just an empty box, lessons learned

Rear abs sensors ordered again. Someone threw them away, money straight down the drain. Im not the one paying again but its soul destroying, the price doesnt matter if It was a box of fresh doughnuts Id feel the same way, waste is waste..

Considering they will be a common size. My asts use an odd size for the rears.

I just watched this and thought it was satire until they said they interviewed war veterans. It looks like a game in the beta stage for xbox 360. AWFUL

Cant say for them but so far AST mounts and BC mounts both silent. The asts were getting a bit older one started to making some creaking noise could of been just some grease needed, I think the bcs design would last longer without noises though. 130 quid off kam racing and caster/camber adjustable

Might of done might of not. Will it be fucked if it has?