Search results

Just wondering if anyone can confirm whether the 172 Xenon headlights are still available from Renault? I believe the part numbers are 7701051794 (drivers side) and 7701051793 (passenger side). Cheers

Recently I got a replacement oil cap for my Ph2 172 - Part No 8200062947 - but it doesn't seem to fit :( The diameter of the cap is slightly larger than the original cap and means that the side of the inlet manifold runner interferes with it, and I physically can't secure down onto the engine...

In the last week I have been getting intermittent, tending to in the last day or so more permanent AIRBAG + SERV lights on the dash - though when I start the car no lights show for a few seconds before they come on again. I had hoped it was the common pretensioner connector issue under the seats...

Howdy all - apologies in advance for the long winded post! I am looking for some advice regarding the suspension on my 172. Currently I am running Koni yellows with Eibach Sportlines, but will be getting my hands on a rollcentre kit shortly. Now I understand that if I were to run the...

Thought I'd post a vid of a lap of Phillip Island in my 172, just in case anyone was wondering what it would be like in their Clio :tonguewink: Running AD08Rs on Turinis, koni yellows/sportlines, camber bolts, solid topmounts, ktec/vibratechnic engine mounts, DS2500 front pads/Motul RBF600...

Hiyas Part number for Clio 1*2 throttle body is 8200110998 or 8200110994, which is also the part number for the Twingo 133 throttle body. From pics they look identical. I am right in thinking they are the same part yeah? Just wanting to confirm before I go ahead and order one that is listed...

Right - a bit of background. Currently running Sportlines/Konis/Compbrake topmounts with Turinis/205/45/16's and am keen to raise the front of the car up a bit - say 10mm or so. The reasons I am keen to do this are: I currently get a little bit of rubbing on the liner near the front bumper...

G'day CSers I am looking to 3d scan a complete thumb grip and then have it 3d printed - I just need one and I can then mirror the file to print off 2. Is it possible to separate the thumb grips from the wheel itself? I assume so but not 100% sure. Currently my thumb grips are ok but I have...

Noticed this on the car for a while now. Everything on the trip computer all works fine but the 'mileage since last reset' won't go higher than 999kms - in other words it hits 999km and then goes back to 0km. I could have sworn that it used to but just in-case I am imagining things, am I right...

Full disclosure - I have Vibratechnics/Ktec engine mounts and Powerflex dogbone bushes in my 172 and with those it had a bit of increased vibration over the oem mounts but tbh not much (I was fairly careful with the installation :) ) Now, I did a trackday last month and the car was great...

Hi Had DS2500's (FCP565H) fitted on the front along with new front rotors and bedded brakes in as directed. Have now got a squeak coming from the passenger side front when not on the brakes and at all speeds but it isn't constant and comes'n'goes. Symptoms include: - sound is a...

Does anyone know if it is possible to fit 182 driveshafts and hubs onto a Ph2 172? I know 182 driveshafts won't fit onto a 172 due to the driveshaft cv/hub end being different (location of abs ring etc), but if you were to fit 182 hubs then the 182 driveshafts should fit yes? I assume the 182...

I have the dreaded driveshaft knocking on my 2002 FF172 and I've been damn near tearing my hair out. I was experiencing it with -1.5degrees camber on high load left hand corners - awful, awful feeling. I have been speaking to people over here in Oz about it, there are a few guys here on OzRS...