Request: Catcams 428 rolling road data

[Quade]

Im quite possibly thinking of going down the cams route with my 172 cup. Deffo thinking of having catcam 428's to finish the spec of my engine (plus can be mapped on the standard ecu). Was hoping some of you who have fitted these can post up your rolling road results so i can compare it against my car in its current spec (i know all rolling roads are different but worth a go) Even better if you have a before and after cams power graph.

Cheers

Dan

 

[Icarus]

Generaly speaking a healthy F4R 736/738 will make around 190bhp on 428's with some form of standard inlet manifold on there.

Cheers
M

 

[matty172cup]

hmmm sounds good to me cost alot of wonga tho but i found on kamracing catcams for £425

Matty

 

[172Ben]

hmmm sounds good to me cost alot of wonga tho but i found on kamracing catcams for £425

Matty

Link?

All i can find on there is £560.00 Inc VAT


http://www.kamracing.co.uk/club-dis...2428-fast-road-camshafts-clio-mk2-rs-864.html

 

[Johnc172]

To give you an idea, before inlets and cams, my cup produced 188hp @ the Surrey Rolling Road Day. After fitting AWT inlets and 428s I produced 203hp

 

[Johnc172]

I'll try and upload my before and after graphs for you

 

[Sean.]

lol, not slating your figures johnc172, id be very pleased with them but 203 bhp is just not achieveable with that spec list. you'd be happy with that figure from ITB's and cams let alone, std inlets!

just to put it into perspective, my ITB'd clio on std cams only made 198!

but thats rolling roads for you, massivly inaccurate across the country!

 

[Johnc172]

That was at the fly, not wheels

 

[Johnc172]

Here's a vid Markcup took at the RR day

http://www.youtube.com/watch?v=DeljoLYKC2Y

 

[fil_b]

lol, not slating your figures johnc172, id be very pleased with them but 203 bhp is just not achieveable with that spec list. you'd be happy with that figure from ITB's and cams let alone, std inlets!

just to put it into perspective, my ITB'd clio on std cams only made 198!

but thats rolling roads for you, massivly inaccurate across the country!

alot of that depends what other mods he had to get to 180 plus (remap, filter cat back system etc)

 

[TooneySonic]

To give you an idea, before inlets and cams, my cup produced 188hp @ the Surrey Rolling Road Day. After fitting AWT inlets and 428s I produced 203hp

pmsl, very generous rolling road there. how did the car compare to a standard one at the rr day? what was the wheel hp?

for the OP - with remap i gained 8bhp and 10lb/ft, adding cams, decat and matched inlets to that saw a further 12bhp (cant remember torque figure tbh). so in total i gained 20bhp from the lot but that does not tell the story of the gains across the whole rev range....

 

[fil_b]

pmsl, very generous rolling road there. how did the car compare to a standard one at the rr day? what was the wheel hp?

for the OP - with remap i gained 8bhp and 10lb/ft, adding cams, decat and matched inlets to that saw a further 12bhp (cant remember torque figure tbh). so in total i gained 20bhp from the lot but that does not tell the story of the gains across the whole rev range....

how u found schrick to the catcams??

much difference??

 

[Johnc172]

pmsl, very generous rolling road there. how did the car compare to a standard one at the rr day? what was the wheel hp?

for the OP - with remap i gained 8bhp and 10lb/ft, adding cams, decat and matched inlets to that saw a further 12bhp (cant remember torque figure tbh). so in total i gained 20bhp from the lot but that does not tell the story of the gains across the whole rev range....

Blah blah figures figures - who cares! Goes well, that's all I care!

When's the next southern RR day LOL!

 

[Martin_172]

pmsl, very generous rolling road there.

disagree to be honest, i ran 188bhp at the scottish RR day on the same day standard 172s were running 160-170bhp and 182s running 170-180bhp, 225bhp focus ST ran 220bhp too

 

[Cro]

Ever had it done again dude?

On a side note, What is the difference between the different profiles and brands? I.e 421s, 422s, 428s, schricks, colombo and bariani? is it a major difference in torque or bhp in any of them or is it more of a case of when the peak occurs?

 

[Sean.]

slightly different profiles across the range, perhaps slightly different materials.

 

[Johnc172]

Ever had it done again dude?

Not since the last time, before inlets and cams, I had it done quite a few times all mid 180s, figures will never impress people on here though lol!

You could have a genuine 350hp clio and someone would still complain

 

[TooneySonic]

Blah blah figures figures - who cares! Goes well, that's all I care!

When's the next southern RR day LOL!

exactly thats the whole point!! glad your enjoying it!!

 

[TooneySonic]

how u found schrick to the catcams??

much difference??

never used catcams so cant comment i'm afraid, cant go wrong with either tbh

 

[fil_b]

never used catcams so cant comment i'm afraid, cant go wrong with either tbh

i want cams and wandered if there is a difference