What's new
By:
Filters
ClioSport.net

Register a free account today to become a member!
Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

Recent content by agressif

  1. A

    Armtech / Omex Rev limiter

    Hi, Has someone ever tested Armtech SpeedShift or Omex Rev Limiter? I'm looking for instructions to feet on Clio Williams. Thank You.
  2. A

    Question about OMEX 600 ECU on Clio

    Nothing new?
  3. A

    Question about OMEX 600 ECU on Clio

    I need it just after mapping to do emission correction What about the loom? is it well wired?
  4. A

    Question about OMEX 600 ECU on Clio

    Is Omex 600 able to do wideband correction according to the OX target map?
  5. A

    Question about OMEX 600 ECU on Clio

    I have LC-1 innovate wide band plugged on it
  6. A

    Question about OMEX 600 ECU on Clio

    Could you confirm my loom is good please? Coil (Clio RS SAGEM/VALEO): pin1: violet wire pin2: yellow wire pin3: +12v pin4: nothing Having the car in front of me, spark wire is plugged from right to left (1, 2, 3, 4; according to the coil number) Injectors: brown wire for left and right...
  7. A

    Question about OMEX 600 ECU on Clio

    Thanks. I have 315cc at 3bar
  8. A

    Question about OMEX 600 ECU on Clio

    I have found it! it was the Ign r****d RPM table. Spark total is ok now What about the high exhaust gas temperature?
  9. A

    Question about OMEX 600 ECU on Clio

    I have set it to 1.70 teeth. On idle it seems to be ok my main ignition map advance value is the same as "Spark total" (Basic idle options are off). But when I load the engine at 30% TPS for example, "Spark total" is about -7° in spite of the value I have put in the main map ignition...
  10. A

    Question about OMEX 600 ECU on Clio

    Thank you. What about the cranksensor wiring? Omex blue / red loom wire for A or B pin? Regards.
  11. A

    Question about OMEX 600 ECU on Clio

    I have F4R flywheel, the engine starts. The only thing is that my map advance in not real because of the ignition timing alignment. Omex couldn't give me the good value for Renault car and I don't have strobe light to check it. On OMEX ECU you have to put the 90° BTDC in "Teeth" and not in...
  12. A

    Question about OMEX 600 ECU on Clio

    I can't PM you, check your security settings. My email: agressif@hotmail.com
  13. A

    Question about OMEX 600 ECU on Clio

    I have ever asked OMEX for but they don't know the right Renault car value (sensors and timing alignment) and they send me to find it myself. It's the reason why i'm asking for Renault car users who has their ECU runing good.
  14. A

    Question about OMEX 600 ECU on Clio

    How can I PM ask users? I have this message: ....... has chosen not to receive private messages or may not be allowed to receive private messages. Therefore you may not send your message to him/her.
  15. A

    Question about OMEX 600 ECU on Clio

    I mean the timing pattern on the flywheel BTDC. I have 1.60 Teeth on my map file. Is it the right value for 60-2, 90° BTDC ? I saw how to configure it in the manual but if someone has ever done it (heat water and quote coolant raw etc...) to avoid me wasting time.
See more
Top