Search results

my manifold has cracked at the bottom, pissed off to say the least, can you order just the bottom half off a supersprint manifold or do you need to buy the whole lot?

???????

http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=8060550403 buy buy buy

read a few diffrent way's but can someone who has done it themself tell me how they did it. thanks.

midge woz ere?

the tuning company..

how much wieght would i need to lose to gain 1bhp per ton on a williams running 172bhp??

someone help my valver has an oil leak, it seams to be coming from below the dizzy somewhere covering the starter motor, its not losing loads of oil but it is losing oil which cant be good, anyone have an idea?

ive got a bit of an oil leak all round the area under the dizzy is covered in oil so is the gearbox/stater motor, this engine has just been built and put in so i realy hope its nothing serious, someone said it might be the head gasket?? in the picture ive done an arrow to the pipe, what is...

just got back from Wales having my valver converted to a 2.0, some of you will know the guy who did, his called Craig and often on this forum and williamsclio, he did the whole conversion in a day, there was one problem and that was when it was all done the engine was leaking oil and so he kept...

made myself, thankyou middo and has for your help, both for sale by the way door badges £15 delivered, engine cover £25 delivered, the engine cover is not quite straight, check pics

..

ive searched the net and i cant find how you make a mould so you can make stuff like bonnets/door cards e.t.c e.t.c. im going to have a go at doing some small bits on my car by 'skinning' them however i'd prefer to make a mould for the bigger stuff i may try.

ive had a quoate from hillpower that was good but his very far away, had a quoate from gdi that was double that of hillpower's, and chipwizards guy is always busy and also very far... is there anywhere else? somewhere closer ? do k-tec and bb do mapping?

as above, what performance mods have you done to your hybrid and what power isit putting out if known.

please.

i dont have a steady hand, but i think its pretty :)

i think it looks pretty, All opionions welcome

any good? ?

as local as you can to south east london, cars going to be a 2.0 hybrid with a williams ecu. cams,headwork,supersprint manifold, the guy doing my engine recomends chip wizards but thats a fair old distance..

the one at the bottom where it meets the cat? lamba sensor?

ok its still not 100% perfect but its 100% better than it was and im sure with more fiddling of the brackets i could get it fine, i dont think anyone will notice it now though. this was the problem - the lip that you can just about see curving off to the left isnt ment to be there, on...

after struggling for ages trying to mount my carbon bonnet properly, the only way i can see to do it is to use pins at the windscreen end off the bonnet, where could i mount them? i cant see anywhere? other people must have done it before...

the pictures arnt very good, cant seem to photo it right.

this is very iritating and feels like its pulling the car back when hammering it, it sounds like its coming from the sunroof but that all looks ok, anyone have any ideas?

very very light, good quality, and i asked him to make it to fit the origanol rain catcher, wont be going on the car until the hybrid lump goes in, but its pretty :)

want to get one, ive considered k-tec's one as i could fit it myself e.t.c but i know thier not good..

whcih would you personaly go for

anyone have this set up ? im sure someone had a cup like this, or if someone can do a photoshop of a valver with carbon bonnet and white willy wheels i'd be well happy.

172 or a 182 near south mimms service's was in a blue valver.