Search results

Mine snapped 2 years old and 5k

I’ve got some Evo 9 ones that have been in my Clio for sale

While cleaning up some surface rust today I decided to remove the bungs under the front floor. On removal of the bungs I found a lot of rust sitting in there. Removed some under seal to find this. The main rust looks like it’s on the inner chassis rail. I can’t imagine that’s going to clean up...

Just cleaning up some 197/200 cams are these standard? I can’t see any Renault part numbers.

kept it in the garage for a few years and think i binned it when i moved.

Maybe mine was boxed wrong then. it was about 10-15cm shorter, i emailed them with pictures and they just said that's the only one they list

Has anyone had any recent experience with tessa motorsport? He now makes the manifolds out of billet instead of cast, I've read the horror story's of cracking manifolds but was wondering if anyone has any experience of the new ones. He admitted there were issues with the cast ones but billet...

is it a cup/cup pack? If so J&r ones don’t fit they are too short

high torque milwaukee 1/2 m18, not found anything yet it can't undo beats all the snap on/dewault guns the other techs at work have. i have the m12 3/8 with a 6 ah battery which would be ok to get some wheel nuts off, but probably not if rusted.

Did you find a sensor that fitted?

I was thinking I might wait for the newer ones but reading some reviews/people guessing, looks like they maybe all for higher end models. Which will be way out of my budget.

Looking at getting either a pro or an air m1. Slight concern with the air is the lack of a fan, Will this be an issue as the laptops get older? Not sure about the Touch Bar but never used one. Looking at getting a 512gb one my old laptop had a 750gb hard drive. I take it I can just restore...

https://www.ebay.co.uk/itm/CAN-Clip-V178-For-Renault-Latest-Renault-Diagnostic-Tool-Vehicle-Diagnostic-Tool/154070397400?_trkparms=ispr%3D1&hash=item23df4fb1d8:g:plkAAOSwqWtdOWVO&amdata=enc%3AAQAFAAACcBaobrjLl8XobRIiIML1V4Imu%252Fn%252BzU5L90Z278x5ickkxGz2ccqatkEnoeekHqhLkVgKJtt27wugVU53aIeQ5Ztdi...

Dragging this old thread up again. Is this the right clip? Says it’s the latest software, is that too late for a 182?

Am I right in thinking 2012 was the last year you could change bits inside like ram and batteries etc? I’ve been looking around at newer ones, but mine had a 750 gb hard drive. So will need another one with a large Hard drive. Which seems to make them very expensive

Hey guys. My early 2011 mbp has died and I think it might be a logic board issue. About 5 months ago it would occasionally not start and stay on a black screen with 3 beeps. I found a guide online and found this to be a bad ram slot. So I’ve been running it with just 1 4gb of ram. When...

I think the problem is due to hotter ambient temperatures overnight. I’m suspecting the fuel pump/regulator is allowing the pressure to release when the ambient temperature is hotter.

My cooksport spring snapped, they were 13 months and 7,000 miles old. cooksport didn't want to know. all i wanted was one new spring. Changed to gaz coilovers from kamracing. 3 years and 10 trackdays later no issues. *touches wood

Fitted some evo seats

My exhaust expanded on track so it touched the bumper.

They'll be fine, mine were like this after the morning at brands

All engine mounts are new, its actually due to the fact the outer boot pretty much melted on track and spat its grease everywhere. some how the boots twisted round too. it actually started knocking 1 day after the trackday.

dont get a j&r driveshaft. i fitted mine drove home from work and the vibration was horrendous. put the old one back on. still not got a refund!. also dont get a shaftec one, one lasted 3 months the latest one lasted 3 weeks. Are the shafts that ktec sell actually genuine?

What other things don't work in the car? Have you tested the charging rate?

On the p1's it's always worth disconnecting the battery and removing the cem. Blow it out and refit it. They also suffer with slack pin tension on the networks

What engine is it?

where do you get them from?

I need some new stickers for mine, how much were they?

I've got gaz gha's fitted to my car. Done two track days with them fitted, they have made the car handle really well. I liked the fact the rears were coil over too.

I hate it, Always feels like it does it at the wrong times. Although it is destroying clutch's and flywheel's so thats good for my work.