Search results

Bingo! Still need to sort pictures out for him.

Yea I can't guarantee they'll be A1 I can PM you pictures of them tomorrow.

I may have front and a rear bumper you can have for that. Considering you go to the Yorkshire meet, May have a few scuffs here and there but I can double check. At least you're hoping to de-chav it, you'll see sense when you go to meets and what looks best.

Found this. Mounted from right to left with 17mm nut on top then fitted under the car etc... If only it was just as simple as...

From what I can remember. 21mm nut Top hat Chassis 17mm nut Rubber mount Bearing (looks like a washer) - works one way only Then the dome Etc... If that doesn't help I'll grab pictures of some scrap coilovers I have tomorrow, I'm sure someone has done an exploded view of the assembly.

Left hand side as less weight/stress is on the bearing.

If you upload a picture of the parts you have it'd be easier for someone to help. I would if mine were off the car ;). I have TA's so should be the same.

These can't be genuine roads... ;)

The 2 torx are above the heater panel inside the head unit you may need to remove a cage if you have an aftermarket stereo. After that it's a case or wriggling the unit enough so you can get your hands round the back to remove the adjustment wires, they're a bit stubborn too. Getting the unit...

I'd go with ET25 with 12mm spacers that would be the exact track width. As above the 12mm per side.

The Snakes Pass is NW ;)

There's a Yorshire Meet on 16/02 at 1pm at Snakes Pass Inn. I'm attending that as it's only 35mins away - S33 0BJ for anyone interested.

There is no difference in size. The difference is to the amount of legs on the SMD. As Alex said above treat PLCC-4 as a 3 poled negative LED. Leemitch-91 if you have no soldering experience I'd say 8-9, with experience I'd say 6-7 as a steady hand and a fine tip is needed.

495

1: Spinksy (convoy from doncaster) 2: Smiggy 3: newb 4: Rodg241 5: kchristmas 6: SteveBall 7: jaysmith 8: Johnpacey1 9: aliengreenAlex 10: KarlMunday 11: Craig_fell (work dependant) 12: Yorkshire 13: newb (convoy from doncaster) 14: HMS Derv Destroyer (convoy from doncaster) 15: DannyB leeds lad...

I'm up for this only 35mins away from me, good living near to Glossop. Always love driving the pass.

If your start of VIN starts CB0A then this could be the number. Traders are on here to provide a service, they'll be your best bet. This is what is said in post #4

alexr19 from CSS.

Welcome pal, the 1.2 G is the amount of fuel consumed since last trip reset. The options can be cycled via a button on the end of the right stalk. Here you will see mileage - distance covered - fuel used (in gallons) - distance left - mpg. Sure that's it, get a couple of pics up if it's a looker.

tayf 172 16" alloys so Renault OEM

Without tints, alloys, bore exhaust it was nice but compared to my old Platinum Silver I found this silver dull.

How modified? These were of a friends, I disliked it.

Other than sanding down the existing filter with wet n dry. It's the next best thing, although it still didn't diffuse the light fully.

Used a mixture of clear book backing (adhesive) and clear/white latex gloves lol.

So after long debate after a wheel bearing decided to s**t itself and lining coming off a rear shoe. I priced up the cost to fix it against converting to a 1*2 rear beam. I decided for the latter and today I bled the brakes, went out for a test drive needless to say I'm happy as Larry...

PLCC-2 3528 I think off my head. Not 0603 afaik. You need 10 of the above for a ph2 and RS. Ph3 you need PLCC-4.

For LEDs I'd try crazyLEDs, phenoptix, modiify or eBay. Both companies are on eBay too. Could try adapting a background from a PH1 as they are a white/off white colour.

Haha. 60mm is verging coilover territory so expect a harsh ride. Even a smaller drop is nice I reckon your wheels will suit a smaller drop than 60mm say 40mm. I live off cobbles and coilivers are liveable, we're only young once.

Looks Inferno from the lighting and the potato you took it with ;) Good job, I actually like them wheels too. A subtle drop that would look ace!

Without looking at any pictures my guess it's possible using skew and distort, this'll be in the image tab under free transform iirc.