Search results

Going into renault in a min to pick up a new gasket, dont know its name and dont wanna look a fool trying to explain were it goes. Pic.. Goes between the block and that casing, and the gear that goes on the end of the shaft drives the oil pump.

Starting to collect some bits for the project now, will be looking for a 172 cup master cylinder because im going to loose the ABS to save more space and have better responding breaks. My father managed to bring me home 8mm O.D x 0.6mm x 10M of copper tube, was hoping to use this to replace all...

My Clio seems to be burning oil, the oil ran low all of a sudden, and its caused some damage, were not sure if its a piston ring thats seized, or wether the valve stem oil seals are ruined, but tomorrow my father is bringing home a compression test. Could someone tell me what psi each cylinder...

Drove past me on the coast road between Aberthaw and Rhoose, saw you had a quick look at my car then you were past, we were both going pretty quick, think this is the same one i spotted in tesco! :cool:

Right, Following on from this... http://www.cliosport.net/forum/showthread.php?t=501312 I have nearly completed my box. I talked to Rob yesterday lunch and he advised me to remove the Iso bar in the boot, being as it was never used by us, i asked him what it was for, was told its for a...

I have decided to build my own sub box and make my own set up, like many people have done. I ordered a terminal to go on the side of my sub box, (...

I haven't bought a sub yet, but decided I'm going to make the box my self. Me and the girlfriend decided to run the remote wire to the boot tonight ready for when i get all the stuff, head unit out, found the remote wire, said 0.3 something on a sleeve on the cable? just cut it off, found some...

I got a quote from Adrian Flux, of 1095, Fully comp, on my 1.2 8V 2002 Clio, Thought this was good, considering i know some of my mates are paying 1500 and more for the same car!.. Mum had a chat with Admerial? (SP?) Mum down as proposer, Me and dad as named drivers, all fully comp, was bang...

I followed you from Rhoose point (i think IIRC) to tesco, i was using the hole in the wall, and you (with red hoodie on) come and stood and used the one next to me, I would have said hi, but i only noticed it was you when i was driving out of tesco heading to the scrap yard, and i saw you...

On tuesday me and Dan are moving my battery to the boot, so today i measured my battery, it was 8" in length and 7 in width, so i made a plate to go in the bottom, made it out of stainless, made it 7" in length and 6 in width, Found some bolts the right length, couple of washers for each bolt...

Just got quoted 2750, EEK!

I cant find the full engine code on my clio's engine as its still sat in the car and i cant spot the tag anywere! info: PE02 GMU 1.2 8V Sagem ECU Cheers! Edit: sorry if its in the wrong section of the forum, didnt know were to put it.

Basically i can have the full suspension (Springs, shocks, etc) from a cup, for free. Now as far as i'm aware, They are the same chassis? (apart from wings and stuff) Im just worried there will be some complications such as rubbing? fitting difficulties? etc, is there anything thats gonna stop...

How many wires (on the loom side) should the lambda sensor have on a F7P Valver engine? Connection is missing off my loom think it broke and i chopped it off before, cant remember how many wires it has. Cheers.

Spotted in the birmingham direction, i was on the back of a bike, part of a group, just come back form the big show.

I decided to start a new thread as the old one it was all out of order and before it was to late I decided to correct my self. My brother, Lee, bought this engine off EBay as a project, got into it, times moved on, he moved to Bristol, was working away, not here very often. I decided to buy it...

The missus just asked me what i want, Im thinking forza, Whats everyone else think?

I have the meguiars clay kit, with applying pads, also have a lambswoll mit, chamoise, few microfiber towels, a machine polisher, just need to know what polish you think i should buy? i dont want to go too expencive, just need to remove all the marks and sqirls from my car. I have been...

For each speaker you obviously have a positive and a earth, when i bought my speaker connections for the speaker end of the cable, it come with 2 big connections and 2 small's, i want to crack on with soldering them on tonight, which one is which?

I am going to be putting a 182 front end on my clio and same for the back, just wondering if the wings on a 182 are the same as my 2002 Mk2Ph2 1.2?

is one half silver and the other half copper? Is this alright for wiring up the rear speakers to my new head unit? if so will order now, Cheers...

Would i be able to get these in halfords? i know they are normally pretty good, its just i need to add another 4 pins to the sound connection block for the rear speakers to go in, in my 1.2, hoping to go get this friday, cheers :)

got this for our 2 year anniversary .. http://www.sony.co.uk/product/ica-in-car-cd-radio-tuners-with-mp3-cd/cdx-gt230, Im not sure what setup to run and what i need to buy? i dont want to use the standard speakers in my PH2MK2 as there alright but i want better, so want to change them in the...

Anyone know a rough price of piston rings for the 1.8 16V F7P valver engine? Just curious and i obviously cant get hold of a motorfactors this time of night...

How does everyone apply these so they go on straight? do you use lines of tape? Pocket level? Or do you just do it by eye? Will be applying mine shortly as my member pack turned up the other day,

Decided im going to use the Audi 1.8T cast manifold as i am turbo'ing the F7P for my little clio, anyways, before i make my old man machine me a adapter plate, to go inbetween the head and the audi manifold, adapter plate bolts to head, manifold bolts to adapter plate, (studs) Only concern, is...

Or is it just a sealant like hylomar? As when my brother took it off for a new thermostat, he used hylomar to seal it back on and it didnt look right to me, should there be a paper gasket? as i have taken it off now and was planning on making one? :S

Hi guys, Borrowing one of these from one of my mates.. http://www.pma-show.com/0351/sony/digitalcameras/digitalcamera/ And he didnt supply the USB lead as he "lost it" I have had it for a week and been itching to get some high quality images of my engine project, instead of the s**t phone...

The engine i am currently building my bro had origionally, and i decided to take and completly strip it down and go for a propper rebuild, anyways, the pistons he got my dad to machine for low comp, ie were worth some money and he needed it so he sold the pistons, were can i get some second hand?

Anyone know what this is? Building my block and mines going back on tomorrow morning, and i lent my manual to my mate and wont be getting it back till lunch time?