Search results

Its fine. No problem.

Thanks for the feedback. Yes, I’ve also already installed the higher-flow pumps that PMS uses. But I’m curious about what the differences are with these pumps. Thanks

Hello guys. Can anyone tell me what the difference is between the following oil pump part numbers? Oem ref: 150100565R Clio 3 R3 ref: 8200279948 Clio 3 R3 Maxi / Acess ref: 77 11160372 Cheers All the best

Hi everyone, does anyone have the service manual for the TL4 gearbox? Cheers

Hi, I usually rebuild Renault engines, and half of the F4R engines I receive for rebuild have the second cylinder big end bearing staring to "seize" or "bearing wear". I can see in the 3 crank types Foged 172, Not Forged and Forged 197. About the pressure I can't say it. In may track car when...

Hello, can anyone explain to me why the 2nd cylinder big en bearings get seized/destroyed in track use or race use? I can identify it in lots of engines failures. Regards

Hello, any one had problems with the automatic tensioner width wild cams? Like Piston to Valve distance changing over RPM Range? Regards Ivo

Hello guys! Im looking for picture parts I need 2x Lifter + Rocker Anyone have it for sale or know where I can get it? I try to get them from Sodemo but no answer. Impossible contact. Cheers Ivo

XPower Equipamentos a Portuguese Company ECU Wiring and Mapping experts. Cheers

All the 433, 431 and 434 make good power, I would chose the cam regarding in on what type and gear ratio or engine preparation. 434 make a very linear/flat torque curve, not the big torque at 5800rpm that 433 makes. The engine made 245hp at 7800rpm (Engine) and 245Nm, similar curves that...

Yes and already raced, but broken gearbox now.

I build and engine with 434 from cat recently. You will get a very tigth intake Valve to Piston distance but OK at 4.30mm TDC timing in case you are using Wossner std rod size, If you use the long rod version Piston KIT (Super car) you will get some extra 1mm aprox. Regards

About the timing on 197s l, its a matter of piston valve distance on intake, i didnt remember the axact advance on intake, I measured the and 8° After TDC Valve to Piston distance and I use that as Limit. On exhaust You can r****d a little.

The reference that I have in my Dyno tests, are from head face to the end of trumpet. I run 3 trumpet sizes on 45mm Jenvey with both, Cat 421 and Clio 197 25cm: best option for track power up to 7600 very stable AFR. 229Nm 213hp at 7200 28cm: best option rally, more 5nm at mid range up to...

Hi, what diameter are your ITBs?

Thanks for the feedback 👌🏻

Thanks for the feedback! I will go for the Non Cup! 🙂

Yes, Im running lowering springs.

Hello guys, the shock absorbers (KYB) from my Clio 197 they need to be replaced, any suggestion? I woul like to keep std system (not coil over). The Clio 197 cup absorbers are diferent than non cup? Thanks

Hello guys, first of all Happy New Year! I’m Re-building a Clio 197 R3 (230hp) engine spec. Anyone knows the big bearings and main bearings clearance ? Anyone have R3 / Maxi engine assembly manual? Thanks

Hello guys, anyone running the Schrick cams 288/280 11.4 lift on Clio 172/182? Cheers

Yeah I have lots of problems with Driver side drive shafts.

Thanks! It was my conclusion after take some measures. :)

Hello guys, anyone knows if the 5th gear of JB3 is interchangeable with JC5? I would like something shorter than 0.79. ideally between 0.82 and 0.85. Thanks

I will go for the AIM Dash, I want to remove some gauges and add another sensors. Like AFR, oil pressure, oil / coolan temperature...

any update? :)

No Answer yet. :(

Thanks guys, I will search more info.

Hello, what are me main difference of the SCENIC 2 160HP Engine F4R to the Megane F4R 225? Thanks

:poop: - 300g