Search results

yep lol thats the reply i was expecting after posting pics!

i think it looks good, you dont have to do what everyone says on here its your own car and i think it looks like a personal car that you have made to what you want! well done

to back up my statement! and clio sport sticker obviously lol dirty as f**k

MINE!

depends on what else you have on your car, what the colour scheme is i think gloss black looks good you do need primer and lacquer as well as paint but i dont know what grade sand paper something fine just to finely rough the surface to make the paint key better.

subtle lol!

ooo tempting the dual optic headlights!

yeh your right but you know how it is you always want to add more bits. no doubt more will probally come although i should put the money towards insurance on a better car when i get one

use the tar remover before the clay just put it on a cloth then apply it to the tar spots and it should dissolve them. i would dry the car before claying but its personal preference srp panel at a time use it thin and remove quite quickly other wise it could get hard to buff off egp do the...

hi these are the pics of my clio i took today. im only 17 so this is all that insurance allows:cry: . modded a few bits on it so its not such a bad car to use while i save up for insurance on something better and faster. list of mods include: 15" dynamique wheels Dynamique spoiler lowered 60mm...

i just bought the bilt hamber clay off ebay should be here tommorrow. i tried the poorboys clay with soapy water and the clay broke down and went really sticky after about 5 mins. that was my first time using clay and it didnt work atall. im hoping bilt hamber will be better and wont break down...

yeh i just unclipped the pas resivour and pushed it to the left then i could see the grommet i didnt have any heat/sound deadening there. just pull it off i assume!

ok cheers guys ill tell him they are wrong and hopefully he will take them back. nick-89 ive pm'd you about the badges

sure was, the seats bolt from underneath ;) never new that!

Speaker wire to the doors pull this multi plug thing apart and then wire the wires straight through it into behind the doors. there is a 2 guides for members As for the tutorials you asked for they can be found in the guides section if you pay the money to become a member there are many...

well ok if you ask clear questions then we will more than happily answer you! power cable through the bulk head question probally the most asked question in this section of the forum? You can find it by laying on your back in the passenger foor well and looking up to the corner of the car and...

the jacking up the car wasn't to change the interior was it:S

purchased some new badges on here to swap my "alize" ones with as they look kind of gay. though o ill look for 16v badges bought these ones arrived today and they arent the right ones. The badges are smaller in every aspect the clips dont line up with my holes on the strips! Are the sidestrips...

lowering without a doubt!

not included im a mechanic and i just had a car tested and it didnt fail on them both bulbs were blown too.

haha lol that really is disgusting inside!

any car clean looks awesome loving the old school astra

probally up there on par with lexus lights and chrome hub cap spinners the worst mods you can do

if you had done a search you would have found how to put the power cable through the bulkhead into the engine bay. if you was a club member then you would have seen the 2 guides to put the speaker wire into the doors!:rasp: if you were to ask nicely and not get angry at every one then maybe...

clifford are good and have mobile fitting vans which go wherever and fit at your home or while your at work.

wire coat hangers bent into U shapes poke them in the holes then apply pressure like your trying to bend them straight again then pull out at the same time and it will pull out easy peasy!

no idea but they look tasty!

i think it would look ok but i wouldn't go for thhe door cards in carbon but everything else is ok. seriously though id get an alarm first!

a custom install is custom so nobody can really help you because it is your own idea! dont get arsey about things if you asked a proper question like eg. how do i mount the amplifier or something like that im sure we can help you out!

if your sanding them down id get them on a belt sander to get the majority of the lettering off then get some fine sandpaper out