Search results

Lol!! He doesn't think those 3 inches will do anything. Besides, he's not got c spanners for them! :(

So the only other outcome would for it to roll stock power, on the nose. Bets seem a bit biased. I'll put money on it not even getting on the rollers.

I doubt we are anywhere near it tbh. When I organised last years at RSTuning, we had approx 30, and were done by 1/2pm.

FINALLY!

OHMYGOD. Want!

Iirc they all use the same. Obviously make sure it's for a 3door car. The trendlines in the trophy are suppose to be lower than standard seats anyway, but I want more of a drop The carpet does rub slightly and is hat to move when nobody is sat on it. But when you're on it, it's easy enough...

I took mine out Jamie and put a washer in so its not on the carpet. It still rubs and it's hard to slide the seat.

Third Time Lucky; Trophy #41 Do they have to be loose mike? TWS want £300+ for drive in drive out.

Re: Third Time Lucky; Trophy #41 Aucky got brand new ones!

Yeah, you'll probably be able to get custom rear shims made up, as there's not much too them. The front's will be a lot harder.

Exactly, that's why I gave him advise, then told him my opinion. Oh yeah, those D90's are 5 lug as well, so you'd need an adapater on there, probably 20mm min, so that going to give a s**t load of poke and scrub.

Yes it is. This is MUCH better for the same price: http://www.cliosport.net/forum/showthread.php?663245-Renaultsport-Clio-182-FF-Racing-Blue-68k-%A33900

As Joe says, camber shims. You can buy them from k-tech, ebay etc. You'll probably only find small minute ones though. If you're going for that look you're going to need a good few degrees. The camber bolts you have will give you a couple of degrees camber MAX. If you want it to look like...

Re: Third Time Lucky; Trophy #41 Hardly looks like your car their Jamie. Its clean!!

Love these, and the noise they make. Power is very good too!

As it's an 8v, I'm going to say unlikely. As said though, take a wheel off and measure it ;)

Awesome, as per.

TRE's are exactly the same, non-sided. As far as I'm aware, Yeah.

Not sure about the wishbones. I thought they were the same, but could be wrong. I'd just get lemforder ones from ECP.

After two months of owning the new Steering rack I finally got around to getting the car book into Birchdown. Car went in on Friday and had the new rack fitted and new PAS fluid, car feels much sharper and there's more steering weight. I'm glad I got it done as at was a bargain and the front end...

Ball Joints and Track Rod End's are the same across all the sports. You can get these from ECP/GSF, note: ball joints are M12 bolts. Wishbones actually come with Ball Joints if you're going to be buying those. I believe these are the same for all sports as well. (K-tec sell them, however...

This works, I've done it. It's not really 'proper' lowering though.

Cheers, Have a look at the Non sport modification thread as well. I didn't really fancy doing the whole 172 bumper thing as at the time it had been done loads and I kinda wanted to do something different. Cheers :D Thanks, I've had a Trophy for about 18months now

That's spot on. They look perfect on 32's.

Have you ever seen Jay's last E46? (on e46zone) His looked fantastic on 32's. http://www.e46zone.com/forum/topic/36054-jays-coop-nature-brown-leather-not-cinnamon-lol/page__st__320#entry540601

Good shout. Must remember to wear something crappy. Can you not use a couple of screwdrivers and hammers ;)

Ahhh right, that explains it. Good to know though. As far as I can tell they look GEN too. Have you thought about any other wheels? I really think they let it down, sorry :(

I had my 1.2 for 3 years. In 2 and a half years all I did was put a K&N on it, Sportlines and some colour coding here and there. In the last 6 months of owning it, I bought coilovers, wheels and an exhaust. I spend about 1k just doing those bits. Love it for what it was, everybody commented...

Most of mine were blurred, or I just didn't like them. So this is what's left: SDC18784 by Jon Garrett, on Flickr SDC18798 by Jon Garrett, on Flickr SDC18800 by Jon Garrett, on Flickr SDC18824 by Jon Garrett, on Flickr SDC18834 by Jon Garrett, on Flickr

LED's really finish it off. I thought it needed re-programming & Xenons to fit LED's?