Search results

Llandudno Garage is where I take mine for work. They have a time served RenaultSport mechanic there. They don't have all the stuff to do alignment though.

Dci had both a 2.75 and 3.25 rack. I got lucky. Within this thread somewhere are the part numbers for both racks.

AJK motors in Llandudno Junction have all the gear but no idea. I go to Buckley Tyres, there the closest place to me that know what they're doing.

http://www.armaspeed.com/eng/goods.php?act=cat&no=53

Is that on the MX5?

I'd run as per your drawing but the 1/4" lines should be 3/16" and the 3/8" should be 1/4".

I needed two clamps on the bottom hose on the rad for it to seal properly.

You drove it?! Does it run ok?

What a shitter, that's awful news. I've pmd you a proposal.

Yes

ebay, panel suppliers, local garages/spray shops. Didn't try Renault as I'd thought the cost would be extortionate

I think there around £20. Put a post up in Renault Wolverhampton under traders for one. Weight lol! They're about a gram!

Yeah that's where I nearly had a moment doing a ton. Kept it planted :) I can only imagine what happens if you lift off there...

Yes I believe so, I have pictures of the hi spec kit under 2118 from someone else on the forum and Dan@SJM runs his wilwoods with 300mm scenic discs under 15s.

Get a 182 exhaust trim, you'll need to cut it slightly bigger but the trim makes it smaller again and looks tidy.

Lol!...Terrible.... Yeah but all the effort is mainly on bolt on bits, yes its some time and effort swapping bits over but its much more cost effective that doing the sills. I did try finding sills and the fact I couldn't find any was the decider. Yes, that's what kept the back end in check!

I'm following! Currently debating whether to have the tailpipe just below like I had on my ph1, cut the bumper like you've done or to fit a stealth tail pipe. That horse is having fun lol!

Back in the game!

I set them in the summer on a hot day (RS day at Oulton) and since then I've only checked hot temperatures so the difference in winter may well be higher.

Sills are shagged

Nice to see a trophy being used properly!

The hi spec 300mm kit is pretty much the same (same callipers and pad size) but with 300mm rotors. I've got a Gen90 ecu for sale if you want something plug and play.

I'm not knocking gaz, but imo the golds are a lot of money for what is still a damper with budget internals.

Any reason for going for gaz gold over some ast sportline 1? Also 650lb is 110nm, so I suppose you won't use it on the road again, unless you don't anyway.

Had a few good sessions in it at Oulton Park on Friday. Beat my previous best wet lap by 5 seconds but nearly had a moment doing a ton going into druids. Yesterday I started taking bits off it to put onto the Cup. Kind of a bittersweet moment knowing how well it went on Friday but hopefully...

It's a load of profiled bits of steel you have to weld onto the beam. The brake pipe bracket needs repositioning too.

I take mine to Buckley Tyres. Its £29 for toe and £49 for camber/caster on the front so similar prices to where Paul goes. My settings are front 3 degrees negative camber, 3.3 degrees positive caster, 20 minutes toe out. On the rear its 1.8 degrees negative camber and parallel toe. I used to...

I haven't tried them on track, only on the road. But they seem to have stiffer sidewalls than the Federals so I'd try 30PSI cold like the AD08R.

I run my AD08R at 30PSI cold, once up to temp they get to around 32-33PSI hot. The RSR I found need a bit more pressure than the AD08, try them around 31-32 cold

Why not get a Gen90? Its plug and play so no wiring needed and it keeps all of the dash lights off.