Search results

Anybody have the part numbers and prices for these or who to see about getting them ? My Hubs are currently of the car and i would like to put some new bearings in before i do some track time. Also after a Bosch Lambda sensor

Any advice on how to remove the above 2 items and what so I need to do it ? i want to get my hubs powder coated so looking to remove these

How hard is this to remove , does it just unbolt or is it abit more complicated on these engines ? I just wanted to get it painted or powder coated

Ive just re-nstalled my engine last night on my own after it sitting in my garage for over a year ! Ive noticed that the engine sits on a angle ? the front of the engine sits higher than the back at a angle I assume this is correct as the lower engine mount is in position and the upper engine...

Any advice on people best methods for aligning up and bolting gearbox together ? Am I best using the engine crane to lift the box or would it better 2 of picking it up and aligning onto the shaft ? cheers finch

Where can i get some of these from ? Ive noticed one has a slit in it cheers

Anybody know roughly how much the above gaskets are ? Any other gaskets worth changing while i put the engine back in ? cheers Finch

Im going to repalce the track rod end , wishbone and ball joints ? Is everybody using genuine renault parts ? if so how much ? or is a motor factors equivalent ok ? cheers

Ive just removed both of these from the car and was going to send them to pirtek to be repaired. Im not sure if both are leaking or just the one pipe . i'd like both to be replaced then I know I shouldn't have any issues . I found a hole in one pipe but I've got a feeling the other was...

Has anybody got a good guide for this or some good advice for refitment of gearbox to engine and re-installing engine ? Its been a while and im not very familiar with renaults , i removed the engine when i was bored a while back ! Is there any manuals available showing schematic build up of...

Looking to Paint my block in the next few weeks. Ive heard of some paints not being very good and some are. Any recommendations of paint and where to buy ? Looking to paint it black or mat black :approve:

How do i remove the High pressure hose fro the steering rack ? anyone advise what needs to be done to remove it from the rack ? I have disconnected everywhere else just need to remove it from rack now to get it repaired cheers mike

http://www.ebay.co.uk/itm/321030864413?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649

http://www.ebay.co.uk/itm/321030884087?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649

http://www.ebay.co.uk/itm/321030855771?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649

http://www.ebay.co.uk/itm/321030838146?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649

I'm looking to get a list together of all the parts required to carryout the turbo conversion on my clio ph2 172 FF . I have purchased the engine below but i am going to have to start collecting the rest of the parts over time prior to starting the conversion. I have had a quick scan and spoke...

http://www.ebay.co.uk/itm/321030793556?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649

Looks like the leak is coming from the joint to the rubber hose as I can see the fluid at the joint. ive seen on here people getting replacement pipe from a place called pirtek ? Anyone know how much they charge and where are they based ? im in wrexham and work over in widnes. Engine is...

To the people who have carried out Supercharger fitments. did you forge the motor ? If not what sort of figure are the stadard internals happy with ? Whats required ? and rough costs on a budget ? any info and guides would be great mike

Anybody Know where i can get some AST solid top mount to go with my KW variant 2 coilovers ? cheers Mike

What preparation is required ? I'm going to get subframe and afew other bits done Is it just a matter of degreasing ? they will be shot blasted prior i believe thanks mike

Where do you bolt into on the engine block when mounting them on a stand ? Also what size Bolts do i require ? thanks Mike

My Engine is out at the moment for clean up and new parts before finishing it off and getting it ready for track use. Are the standard Genuine Renault clutches up to the job or could anyone recommend what i should get ? cheers mike

Engine is out, Going to take to specialist for cambelt fitment, dephaser pulley, water pump, power steering pump and aux belt kit. I have all the Genuine parts at my house and i'm going to drop the engine off an get t fitted by the professionals. How many hours work would you say to do this...

Started undoing the 2 front subframe bolts at the front and got to a point and the nut inside is spinning ! Just been trying to get a offset spanner in there to grp it but dont seem to fit which ever one i use ! Anyone know what type i need or any advice ! without being to grip these with...

I removed the engine about 2 Months ago so that i can clean up the block and fit some new gaskets etc. I really want to get this on the track for the summer but need alittle help as i dont want to attempt the cambelt myself as i know what can happen ! Anyone Wrexham area or NorthWest fancy...

Whats the best things to use to clean up engine block and gearbox ? I was thinking of a wire brush and some form of de-greaser. Ant particular degreaser people found better or any good methods of preparation for cleaning then painting ?

Some of you may know that i decided to remove the Engine & Gearbox Last weekend. I'm now going to look at removing the Gearbox and clutch so that i can fit the Engine onto the stand for clean up and change various parts. Ive seen on the guide that it just looks like removing around 10 bolts...

Ive started getting my Engine ready for removal bearing in mind i havent done it before and trying to follow guides on here to assist me. Ive removed the majority of things rad, lights cross memeber alternator air con etc. Havent removed driveshafts until i have bought an engine lift ...