Search results

Yes, i run an aftermarket easily enough. You can get a connects2 box for about £15 on here, they come up often. (One here for auction, pretty cheap - should work just fine. Looks identical to the one i had)...

Mine had both, but I also had a satnav, so maybe that made it different? It was a cabasse auditorium in mine. FYI You can't run one of those aux cables, pretty sure they dont work in these. You can instead get a connects2 box that has an aux on it. I personally had one that went to a 30pin...

That blue cable goes to your underseat cd changer. Pull it out.

Those aren't the bearings that are run from standard In the ktec mounts. You're better off just going through ktec as you don't save much money sourcing parts yourself if you can't reuse washer and circlips. The bearings you want are SKF GEH20C, the circlip is 40mm internal and you 32x44 ptfe...

Id try a cheap one first, if it doesn't work send it back

Why you changing out of interest?

You got 3.9 not 0.39 right?

I was zooming into the numberplates on the cars trying to work out wtf you were on about and I've only just realised you meant the food! Looks great as always brigsy and good news on the esp situation

Did you paint and underseal?

https://partsouq.com/en/catalog/genuine/unit?c=Renault&ssd=%24BQoJQHMFBwYESkECVzkHBgcCAgIHBlMbCVNBUVtGc3kFXBsMW1d0BExaWVErVUgCAAwNCwtKWw4LDFFcUFByfgcBWFI_TF5RW0dQW1IONxZdR3R4AQQHAS0bDFFcUFByfQcBUlVIAk1rdVRdV2JGUUwLfAVwE01XRCtV%24&vid=1247&cid=2041733807&uid=3386&q= It gives 3 different numbers...

Amazing work. How much did you remove the paint the rear beam etc on the trophy?

Those liquid gold interior trims looking fresh

To get the flies out try just an airgun through the back. Keep blasting and obliterate them haha. Either that or take it off and all electrics out and flush with distilled water and dry thoroughly. Refurb looks good

They look to be carbon. Might be moulded over the top of the plastic or dipped.

@Dr Jekyll

The seats are common to go there, it's down to the tilt release pull. The mechanism strains the stitches, mines the same but not as bad!

It's only a few mm so no. The wheel wants to be one of your first mods however as it really does make a difference with a smaller one! I like the oem wheel but it is very bus like. I happen to have a momo boss and Sparco Renaultsport wheel for sale ?

Where you from? Car looks good. If you want to retain your standard seats, remove the antivibration washers from beneath the rail. Lowers you a little bit but stops you being able to slide the seat very easily! Worth it for the few mm IMHO.

Those no12 screws I linked to above are incorrect. I wrote 5x25MM but then those linked are 5.5mm, they do not fit. I believe what you actually want are no10 screws that are 4.8mm - i'll get the OEM ones on the verniers tomorrow at work

Just tug the bumper, hard. The brackets on the bumper dont have rounded holes they're just 'forks' if that makes sense. You'll be able to get better access to remove the bolts when you remove the bumper.

Because it has a satnav in it

Mine still has it's 04 disc haha. I'll get round to retrofitting an LCD in the future and using it as a media centre

What clio? If you already have a clio with a satnav dash I see no reason why not.

But then you have holes in the bumper edge which looks messy and archliners free to move slightly. They'd still be held in with fir clips however

I don't run the bolts in the brackets for the bumper but I run all the bolts that hold in the arch liners to the bumper. The ones from ebay just rust so quickly so I wanted some stainless ones to replace them.

Think you're right for the ones on the brackets mate!

https://www.ebay.co.uk/itm/No-12-x-25-SELF-TAPPING-SCREW-PAN-HEAD-TORX-T25-SOCKET-DRIVE-A2-STAINLESS-X-50/140837426422?epid=1888221720&hash=item20ca9094f6:g:LFsAAMXQAF5Rh3vM

5 x 25 t20 I think they are, for anyone who finds this useful! With a 15.5mm washer.

Believe Ive found the genuine part number - 7703017090

The ones that are through the edge of the bumper into the archliner?