Search results

yep sure would im running just a stage 1 high torque map as the injectors hold it back and am getting 120bhp 145lbft 172 injectors added into it and your looking at 135-140bhp, add in an intercooler, exhaust, induction etc and you can get close to the turbos 150bhp limit

wont matter as its a generic map not custom to your mods so while you will likely get a small benefit from an induction kit if done properly it doesn't matter if you do it before or after the map.

mapped DCI's are awesome, by the time you paint your new panels etc then personally I wouldn't think its going to be worth it unless your doing it just purely because you want to! if it was me id just stick a decent suspension setup on it, tidy wheels and rubber, get it mapped and have some...

ebay is your best bet, its not as easy as change the inlet manifold and exhaust manifold and gain 25bhp though the engines run a higher compression ratio and different cams, for the money it would cost you would be better swapping to 2.0 power or boosting your current 1.6

ill have a video up soon of standard exhaust with decat

best bet is to use Twingo RS 133 bits, same basic engine.

no

172 injectors, and RS tuning map! 140bhp 155lb/ft would suit that nicely!!

20% increase in power and about to have a 50% increase in power! Oil is important!

Yeah deffo! I managed to get it for 65 quid from my local factors which didnt seem too bad! Very impressed with it though!

the most expensive engine oil ive ever bought lol

didn't realise you had a LSD now, was just thinking it seemed to be putting power down on corner exit very well!!

id be more interested what it has instead of paddle shift?

smert.

the 1.6 GT has the 6 speed clio 200 box though! as already said, the DCi is the one to go for, 1.6 VVT is pretty gutless in the twingo never mind the Clio 3!

and another view

Cheers guys f1s on this week hopefully

FK 30mm spacers fitted

same as the twingo, and the twingo uses the same front hubs, brakes and mine runs clio wheels so id imagine its exactly the same

ive got FK 30mm bolt to hub spacers for the twingo but the wheel bolts need modified to chop them down as they go through the wheel, spacer then touch the hub before tight

lovely, an R26 is my next car, dying to try one!

a car like that on PCP is proably still going to cost 10k in payments though for the 3yrs, and your restricted in millage, and ideally need to keep it for the full term. depreciation is an issue on them no matter what route you go, I think its either a case of deal with it, or choose another car

wow nice car dude, ive got a red 172 rep...

you install the software on your laptop, plug the rs tuner into the computer/car and take a screenshot and send it to henk, he then sends you the best map for your car

<3 Joes ST!! cleanest one ive saw!

Apparently maxwell had a cracked inlet manifold, thats 2bar for you lol!!

Re: Shell Nitro+ I was running it yesterday for the rolling road and expected lower figures than last time since ambient temps were a bit higher and I run 30c above ambient due to my poor intercooler, yet I ran 2bhp and 2lbft more, down to the fuel? who knows. was running Tesco momentum last time

ha beat me to it there John! cheers Next up it needs brakes as they have hardly any pads left!!! looking at Pug 406 Coupe/Mk1 FRS / Fiat coupe turbo brembos + 172 280mm discs

bit of an update, AP rear dampers are rubbish and knock like mad so swapped them for a pair of Apex ones, problem sorted! Car was on the rollers again, this time made 119.8bhp @ 5000rpm and 146lb/ft @ 3000rpm had a rusty old engine mount cover decided to give it a paint since I had spare...