Search results

You can easily just use a cereal box for that rocker gasket tbh 🤣 it wont matter what you choose Parts wise, the F7P & Clio F7R are pretty much identical apart from the sump pan, crank, pistons, cams and the valves The spanner in the works is that the Megane F7R is half identical and half...

Yeah that's the one, they also sell the front & rear jacking points for the Clio as well

Outer sills don't exist but the lower spec ones simply need to be cut down to size as they're shorter on the 16v/Williams so that's relatively easy There's a company on ebay (can't remember the name but will have to dig about to find it) that does R5 bits & bobs and the inner sills they make for...

You want to click on C57D for the Valver or C57M for the Williams https://www.catcar.info/renault/?lang=en&l=c3Q9PTIwfHxzdHM9PXsiMTAiOiJNb2RlbCIsIjIwIjoiQ2xpbyAocGhhc2UgMSAmIDIpIn18fG5vcHJzPT0xMjYwIiwiMTI2Mnx8YnJhbmQ9PVJlbmF1bHQ%3D

@Williamspaul

Have you removed the alternator belt to try turning it over? Only ask as I've seen seized up alternators, pas pumps and the tensioner pulley stopping them being turned over by hand. Another thing I'd do is remove the rocker cover and the distributor then pour some oil all over the cams & lifters...

It's a bit hard to tell but they might be bigger discs as well, standard size is 259mm and I think there were 4 different size discs available with the Hi-Spec caliper kits back in the day so measuring those discs on it will be useful info for selling the calipers

Get Magnetti Marelli as they're OEM but just make sure they're genuine & from a reputable seller as there's lots of fakes about

I'd say have a look at a policy of it's own for the fiesta with zero NCB Only say that as all my NCB (10 years) is used for my 172 Cup with limited mileage & I'm paying £193 but my daily is a normal 172, 10k miles a year and it's £230 with zero NCB - so it might not be as bad as you think 🤷‍♂️

Depends what the end result you're after looks wise is tbh, on my Williams I was after as close to OEM finish as possible so went with paint But on my track car I wasn't bothered about looks/finish & wanted something durable & cheap so went with gloss black powdercoat

I don't actually know tbh, all I do know is that's it's a period correct race spec engine as he does hill climbs & sprints in it so it's got to be the right spec for the class he runs in

At my workshop and the guy next door is driving about in this

I'm guessing it was probably a comparison to the early ph1 & ph1.5 Valver seats as you sit more on top of them rather than in them

The Williams and ph2 Valvers have the exact same seats, just a different cloth pattern but they certainly are the best of the bunch It was the leather seat option in the Valver that used the R19 front seats

Bordanovasport are spot on, I've bought loads of Williams bits from them over the years

Worse case scenario is you have to get jiggy with a grinder and just chop the bolt

Yep (y) Unfortunately getting the fluid out is going to piss out all over the place & make a mess no matter what you do so use some cardboard & plenty of rags to soak up the worst of it

The pipe circled in red goes to the power steering fluid reservoir and the 1 in green connects to the pump The nut & bolt that connects the column & rack looks like this and it goes on the shaft you circled in green

On the far right of this pic is where the column connects to and the whole lot drops down as in the pic above it

No need to touch any of those, on the bendy joint at the bottom of the steering column, on 1 side of it is a 13mm nut, undo that, pop the bolt out and it's disconnected from the rack

There's an online version of it now...

Here's some diagrams of the system, basically you need a standard fuel rail that has the regulator built into it and the correct pipes Number 5 in this pic is the vacuum pipe that connects to the original regulator

Put it on a Dyno yesterday Not bad for a neglected £1,000 shitter 👀

I'd be looking at the mechanism from underneath to see what it's doing when operated and making sure both back wheels are locking up properly Just a thought plucked from my arse so could be useful or total b****cks but I'm thinking along the lines of the cables not being fully seated in their...

My 1st thought was perhaps it was some kind of cold air feed but there's just solid metal on the other side so god only knows why they did it 🤷‍♂️ Funny story though, the car needed an engine & a guy on here was breaking a cup so I bought the engine & a load of other mechanical bits & bobs at...

Here's a close up of it for you 🤣

Things could always be worse, at least it doesn't look like mine did when I 1st got it

@Williamspaul has got a set of proper Cup Turinis for sale

Not recently but I took that pic a couple of years ago, just your mention of being in the Eifel and a Clio Grand Prix made me remember the photo 😅