Search results

Does everyone's clio not whine in 1st? Mines always done it. Sounds like reverse does 😂

Mines fine and definitely doesn't make that noise. Yours black or red?

Looks great for a wrap though mate! Loads better than how they were glossy. Did you use a hairdryer to soften it when applying?

I mean the surround part is tacky plastic. The top dash centre part if that makes sense haha. I'm not fussed it's not really a big panel so not too scratched

Popped over to see @bloke last weekend to have some black series steering rack and rear beam bushes fitted to complete the Polybush package throughout the car. It's something I wouldn't have wanted to attempt on the floor due to access and it being a pain in the arse! Thankfully all went well...

Box done with northloopcup and either fitted at Mick at diamond or ddc

Halifax Maccies? ;)

Get the box oil changed. Mine used to crunch into 3rd sometimes then after changing the oil it never did it again

Does your gearstick move when putting your foot down? I'm running a vibratechnic solid mount purely for the fact everything else is solid. I think gearbox wise OEM brand new can be decent. It's whether you take the punt and fit and forget solid. Your choice! I'd take a look at the polybushed...

Believe he's talking about a factory 182 wheel, not aftermarket.

There's a guide in the paid up members part for removing the cruise control buttons. All easy to change over. Guides for it all.

Mine doesn't seem to be wearing the carpet or damaging it but it is initially a little hard to move. I never move my seat anyway as I HATE adjusting it. Access the nuts from under the car (2 are hidden behind grommets) then tilt it forwards and backward to reveal the spacers clipped in...

I've posted in my thread with a reply to you if you've seen. There are 3 additional bolts to remove. If you put a jack under the engine or gearbox, then remove the top nut and 2 smaller bolts on the Centre mount itself then lower the jack slightly and tap the mount with a hammer it'll pop it...

You can get away without removing it as you can just grind the captive off the back through the wing then nut and bolt it unless it's moved. There's 3 bolts down there that need removing to access the main mount if your 4th is snapped. Shouldn't need to remove the gearbox mount itself. If you...

Most likely battery going off the symptoms of the needle flickering rapidly. They do this when low. I wouldn't worry, cold weather kills batteries. Just put a multimeter on the terminals whilst running to check it's voltage

I used the red powerflex ones and got no noticeable added vibration. Everything else is black series powerflex though so maybe I just don't notice it! They fitted really easily with a vice. Just need to make sure that all the old rubber is cut out and use fairy liquid on it all. The only gripe...

Just wondering how you know it's 196 bhp as everyone always says the cars are cammed when they're not

What cams you running in your clio?

Just set fire to the car, then you'll have no water issues.

Darren says it's fine

You can get away with removing the driveshaft by removing the tre and balljoint, pushing wishbone down and turning hub right round on lock. It's tight but you can remove the shaft.

You parked behind me whilst I was bowling

Mines firm and other people's ive sat in are the same. I nearly put my foot through the floor when i get in something else

Took me months to find my new BG bonnet and that's not without dents (has a couple very minor ones that I'll get a dent man on eventually). They all seem to be pressed in in the front edge

Looks alright this! Any close up pics?

Brilliant news Steve!

Think ive sorted it. Rushed home after work and got it in the air. Removed the caliper and disc and found some threadlock congealed on both hub face and brake disc. I had recently redone them on this side and to save time not removed the caliper (laziness). I believe this has led to the disc...

Mine showed minimum on dipstick after 7k miles lol