Search results

lol, was fairly warm earlier on though so didnt phase me! Was a right ballache to remove the locking rings though, ended up taking it to my local garage as I didnt have a good enough vice to get them off! Gonna keep them a lot cleaner on the car now though, too much effort to do this every...

Cool, makes me feel better about it, thanks for the replies. It's a Ktec decat. fossie, yeah is a bit, not loads though. although not sure if it would seal better once warm as the car and exhaust was cold when i checked it for blowing.

Cheers Gaz. I'll get it checked when i get it serviced and my new exhaust fitted. When I was under the car revving, there was enough of a gap for some condensation to come out of the gap which isnt good news im guessing, bubbled out quite a bit.

Was under the car today, noticed a slight gap between the decat and manifold: it's blowing slightly from both ends of the decat too, is it just seated slightly incorrectly and will be rectified by refitting? Was only fitted a few months ago proffesionally with a new mani>cat fitting kit.

Decided at work today that I would get around to cleaning all the fonrt suspension down after it no doubt being covered in road salt and crap. Exhaust has been rattling a bit too so decided to check that out, and then make some homemade new mounts due to perished old ones. Started off with the...

Gonna strip my front coils off today and clean them all up, but what can I use to protect them? Previously used copper slip but it makes everything stick to them, so I'm after something I can buy off the shelf today to do a better job.. I was thinking push bike spray on wax lube? Supposed...

Lines fitted and bled by Birchdown, I wouldn't attempt it myself!

Wasn't on track, was braking for around 90 to about 50 and nor even full force as I wasn't 100% pushing it. Granted i'm no race driver but I know when to brake and the speeds I can take the corners, You had a similar set up, so not this set up, and they vary massively so not a great comparison

Not being funny but it clearly isn't. Brakes were bled a few months ago when I had the lines fitted, and this is the first time I've driven it hard since. I brake when I need to, not for the sake of it.

Jonathan, they are official ebc's, my mate never fitted them to his 182 before he sold it so gave them me cheap.

Thanks for the advice, i'll get some before I go on track in the next few months.

^ they were red hot! Like i said, wouldnt have chosen them over the DS2500's if I hadn't got them dirt cheap off a mate.

I've found the redstuff pads really good when hot to be honest, read a lot of bad reviews, and i only got them over DS2500's because they wer ebrand new for £30, but just tonight they wern't upto the job. They were bedded in as per a lot of guides on the net and until now performed well...

Got turini's on it. Oh, and i wasnt riding the brake pedal for miles etc, I know how to brake reasonably well.

Just went out for a 20 mile backroad blast, and my brakes went. Not very good considering I've upgraded them! Got Brembo Max discs (grooved) Redstuff pads Dot 5.1 AP racing fluid Braided lines Not very impressed to be honest! Don't think they will stand up very well to track work :(

Yeah 2 bits, can see the join in the middle. Needs about 2 inches trimming off each end at the wheel arch.

Search my username, i bought them to the forum ;) About £35, very flexible so perfect for low cars. http://www.cliosport.net/forum/showthread.php?t=350258 http://www.cliosport.net/forum/showthread.php?t=388613 A few front shots in them

thanks for the replies. I'll get it on a machine when I get it serviced in the next month or so to find the specific problem. Was fine today though.

Yeah the car is driving etc, then it seems as soon as i pull over it works fine again :S Thanks warren, I'll search his name in this forum and see if it finds anything! Edit - found it, I'll hopefully get it plugged in to a machine somewhere to find the problem.

I've done a search but I'm not searching the right thing, although im sure ive seen threads about it before.... Got in the car tonight, pulled off and it wouldnt go above 2.5krpm, pulled over for a second, rev'd the car out of gear and it was fine again? Then left the gym and it did the same...

Cheers Fred. Still not too sure, it felt perfect for me at neg 2.5 as opposed to the neg 1.5 that I managed to guess it at. I think an advantage to me is that of the 2 set ups I have had (not many I know!) compared to the standard car and then sportlines, the coilovers are 10 times...

Fitting is easy as pie, can be attempted yourself. Not sure how far you are away but if it aint too far I'd do them for you. Setting them up you need a pro place really. They can be guessed by eye but in order for the benefits you need the works, tracking, camber, caster, toe in, and corner...

Without doubt one of the most interesting threads on here. Wondering if someone could answer a few simple questions for me since theres a lot of knowledge looking in! Got H&R's on my car and I'm wanting to set it up for fast road/occasional track use. However I don't know what a happy medium...

Hmm, I'm torn now! I want a YS again.........

Yeah thats the one I'm thinking about....whats the it like? Any pics on the car?

The ultrasport one? I've found some milltek vids on youtube, but cant find much on the ktec's.... chrispy, got any pics of yours? Our cars will be near identical if I buy one of those!!

Not sure which to choose from..... What would people choose, price difference is not worth mentioning, which would be better quality? Car is on a ktec decat at the minute too, I don't want a stupidly loud car, but need to run the decat as it is too low for the standard cat and it hits...

Nice. Whats been done? What power you running now?

One of the best reps I've seen, does the job perfectly mate, credit to you.

That plate is terrible! Rest is nice though!