Search results

I take mine to Buckley Tyres. Its £29 for toe and £49 for camber/caster on the front so similar prices to where Paul goes. My settings are front 3 degrees negative camber, 3.3 degrees positive caster, 20 minutes toe out. On the rear its 1.8 degrees negative camber and parallel toe. I used to...

I haven't tried them on track, only on the road. But they seem to have stiffer sidewalls than the Federals so I'd try 30PSI cold like the AD08R.

I run my AD08R at 30PSI cold, once up to temp they get to around 32-33PSI hot. The RSR I found need a bit more pressure than the AD08, try them around 31-32 cold

Why not get a Gen90? Its plug and play so no wiring needed and it keeps all of the dash lights off.

Yeah that's it, no point if it's no fun. It's parked up next to my cup now so I can strip the parts off to swap over. Yours sounded good going down the pit straight

Ahh yours was the Monaco. Ph1 has itbs, cams, quaife diff, asts and some other bits.

That was me! Which Clio were you in? I saw a black ph2 in a garage I thought might be you but you weren't around to say hi.

I got one the same day!

Fair play, they're very nice figures and its good to see the manifold adding around 10lbft either side of the previous peak torque figure and more top end. Looking at your graph the manifold might even help mine out top end.

Get an adjustable recirculation dump valve, you can tweak the dump/chatter to suit then

Dotted lines before the pms manifold and solid lines after? Can't see the rpm, does it peak at 7500ish?

It didn't drone on the Cup but that had a cat fitted so hopefully that'll sort it for you.

Good tool kits for the money, can't complain about them at all. Shame about the air filter plate, I'd be fuming!

Is it that high due to lacking vvt?

I've been looking at the usual 422/423 but I've also been considering using a 197/200 dephaser with catcams 404 and mapping in the continuous vvt control

Some longer trumpets might help your torque no end, those Titans look really short. The 423s have a peak torque band from about 4.5-7k RPM so short trumpets won't gain you anything there.

Interested to see how you get on without the VVT. I'm debating what to do with my forged engine, would be a waste not putting some BIG cams in down the line.

Is the Yozza better than the Oreca?

Go to a scrap yard or look on ebay for a Mondeo master cylinder. Guarantee you you'll find some cheap or for free. Otherwise you've got the cost of the bias valve and all the pipes and fittings.

Run one of these on each brake line straight off the master cylinder http://www.fordpartsuk.com/shop/ford_mondeo_brake_pressure_reducing_valve___f_1113008_c_806.htm I got mine for free though from a freind with a spare mondeo master cylinder.

I just run Ford in line pressure reducers from the master cylinder to the rear lines. Feels perfect. If you want it adjustable then I would tee both rear lines into one bias valve with 1/4" diameter fittings (its about the same as 2x 3/16" fittings so you don't restrict anything). Then 1/4"...

All the injectors ok? No air leaks? You mean Jenvey ;)

You need 5mm spacers with the ET35 1.2s. I also ground a bit of material off the callipers for better clearance.

Haha yeah I'm not the only one! ;) Its mounted with a alloy bracket I made and a cable tie. The fan is fitted with a fan fitting kit. I'll be selling the rad and fan when I start stripping the silver one.

You don't need camber or 195 tyres tyres for ET35. You can run between ET 45-25 with 195 or 205. ET35 is better for clearance all round with shocks, inner arches etc.

Put a 172 cup gearbox in, it has a better final drive which suits the car much more. The Ph1 box makes it feel a bit lazy in comparison. So get a JC5 129 instead of the JC5 089. Both are speedo drive boxes and a straigh swap for one another.

Its my place of work unfortunately so Friday and Saturday are out. I'll be around there tomorrow from around 7am until about 6.30pm. Otherwise if you pay by gift I'll do them for £35 and get them to the courier tonight so you should have them for the weekend.

Yeah mine came off my Ph1 before I put the Brembos on, they work perfectly. Postage and paypal fees would make it £40. I'd take £25 cash if you collected from CH4 0DR

I've got some ready to post if it helps. £30 in good working order

The current one needs a diff. Surely more power and torque will make this even more apparent...ffs Renault.