Megane R26
I have a real itch recently for a ph1.
Currently in a FF 182, bought cheap a while ago as it's a cat C (wing, xenon and bumper in 2014).
Car is very tidy apart from one Tiny dent and small stonechips on front bumper.
Has a long mot, recent low mileage engine with belts etc, recent clutch and gearbox, driveshafts, the List goes on.
Needs nothing
I was Thinking of breaking it as i won't get much for it as a CatC, no matter how clean and mechanically spot on,pulled a strong 175 bhp at Surrey Rolling Road and stronger than others I've driven recently.
I was looking to make the switch to an r26 but I can't stop looking at Ph1's!
Break the 182 and tranfer good bits onto a ph1?
Bearing in mind cost of tracking, remap and possibly bits like exhaust and New dampers if ph1 is fairly stock.
List of bits on my 182 -
Long mot
Low mileage (67k) 172 lump with belts back in March.oe Clutch at same time
Solid top mounts
Polybushed everything
Ph1 airbox and a fatty as spare
Red ht leads
Cooksport springs
Whiteline rear ARB
Suade snappy wheel
BMs shifter
Mint interior
Cup pack spoiler & splitter
Ktec Janspeed supersport
Rs tuner map
Rs inlets
Camber bolts (fast road geometry set up last week)
Gold 2118 mag, new Federal Rsr
20 & 15mm spacers front & back
New cup dampers
New tre & lower arms
Mintex 1144 & braided brake lines
So I'm looking for a tidy ph1 around £1500 and swap most of the bits over incl 182 manifold, break the mint 182 and have some fun in the ph1.
Good idea? Thing that's putting me off is I drove two 172 cups recently (same plan) but both felt really gutless compared to my 182! Really hoping a ph1 won't disappoint in a straight line.
I'm Handy with a spanner but don't really fancy an engine swap on my drive..
I'd be selling the 182 if it wasn't a Cat C
Pics of the BG -
Currently in a FF 182, bought cheap a while ago as it's a cat C (wing, xenon and bumper in 2014).
Car is very tidy apart from one Tiny dent and small stonechips on front bumper.
Has a long mot, recent low mileage engine with belts etc, recent clutch and gearbox, driveshafts, the List goes on.
Needs nothing
I was Thinking of breaking it as i won't get much for it as a CatC, no matter how clean and mechanically spot on,pulled a strong 175 bhp at Surrey Rolling Road and stronger than others I've driven recently.
I was looking to make the switch to an r26 but I can't stop looking at Ph1's!
Break the 182 and tranfer good bits onto a ph1?
Bearing in mind cost of tracking, remap and possibly bits like exhaust and New dampers if ph1 is fairly stock.
List of bits on my 182 -
Long mot
Low mileage (67k) 172 lump with belts back in March.oe Clutch at same time
Solid top mounts
Polybushed everything
Ph1 airbox and a fatty as spare
Red ht leads
Cooksport springs
Whiteline rear ARB
Suade snappy wheel
BMs shifter
Mint interior
Cup pack spoiler & splitter
Ktec Janspeed supersport
Rs tuner map
Rs inlets
Camber bolts (fast road geometry set up last week)
Gold 2118 mag, new Federal Rsr
20 & 15mm spacers front & back
New cup dampers
New tre & lower arms
Mintex 1144 & braided brake lines
So I'm looking for a tidy ph1 around £1500 and swap most of the bits over incl 182 manifold, break the mint 182 and have some fun in the ph1.
Good idea? Thing that's putting me off is I drove two 172 cups recently (same plan) but both felt really gutless compared to my 182! Really hoping a ph1 won't disappoint in a straight line.
I'm Handy with a spanner but don't really fancy an engine swap on my drive..
I'd be selling the 182 if it wasn't a Cat C
Pics of the BG -