So then, following on this thread - http://www.cliosport.net/forum/showthread.php?648971-New-Car-Content
Since I can't drive the car until the back end of August, I thought I might as well start doing a few little bits to the car.
I started by doing a headlight correction. The top half's of the headlights were the only parts affected, so I taped up a section and wet and dried the top half's. After using Megs Scratch X, I use a Menzena polish and then applied a good few layers of FK1000p. the beading looks great
Before/after's (the before's are taken on my iPhone sorry)
IMG_1037 by Joe_Harding, on Flickr
IMG_3859 by Joe_Harding, on Flickr
IMG_1038 by Joe_Harding, on Flickr
IMG_3857 by Joe_Harding, on Flickr
Next up was a new rear bumper light unit, as they seem to go a bit dull after a while. Again this was protected with a few layers of FK1000p
Before
IMG_3852 by Joe_Harding, on Flickr
After
IMG_3855 by Joe_Harding, on Flickr
I've also bought a few other items to be fitted next weekend, or further on down the line.
I'm not a massive fan of the standard 'Renault Sport' badge, so that will be coming off next weekend before I give the car a detail.
IMG_3856 by Joe_Harding, on Flickr
And then a '197 style' badge will put in it's place
IMG_3862 by Joe_Harding, on Flickr
I've also sourced a decat of the yozza, a Scorpion RS192 one in fact. So that will be going on at some point, when I get a new cat fitting kit and a lambda blanking plug.
IMG_3860 by Joe_Harding, on Flickr
Next weekend I'll be changing the engine and gearbox oil, so I've got a new filter and washers to go on too
IMG_3861 by Joe_Harding, on Flickr
I've also got a new pollen filter to fit next weekend too
IMG_3863 by Joe_Harding, on Flickr
That's it really for now
Since I can't drive the car until the back end of August, I thought I might as well start doing a few little bits to the car.
I started by doing a headlight correction. The top half's of the headlights were the only parts affected, so I taped up a section and wet and dried the top half's. After using Megs Scratch X, I use a Menzena polish and then applied a good few layers of FK1000p. the beading looks great
Before/after's (the before's are taken on my iPhone sorry)
IMG_1037 by Joe_Harding, on Flickr
IMG_3859 by Joe_Harding, on Flickr
IMG_1038 by Joe_Harding, on Flickr
IMG_3857 by Joe_Harding, on Flickr
Next up was a new rear bumper light unit, as they seem to go a bit dull after a while. Again this was protected with a few layers of FK1000p
Before
IMG_3852 by Joe_Harding, on Flickr
After
IMG_3855 by Joe_Harding, on Flickr
I've also bought a few other items to be fitted next weekend, or further on down the line.
I'm not a massive fan of the standard 'Renault Sport' badge, so that will be coming off next weekend before I give the car a detail.
IMG_3856 by Joe_Harding, on Flickr
And then a '197 style' badge will put in it's place
IMG_3862 by Joe_Harding, on Flickr
I've also sourced a decat of the yozza, a Scorpion RS192 one in fact. So that will be going on at some point, when I get a new cat fitting kit and a lambda blanking plug.
IMG_3860 by Joe_Harding, on Flickr
Next weekend I'll be changing the engine and gearbox oil, so I've got a new filter and washers to go on too
IMG_3861 by Joe_Harding, on Flickr
I've also got a new pollen filter to fit next weekend too
IMG_3863 by Joe_Harding, on Flickr
That's it really for now