New Design Samco Inlet Bend

[ClioF1]

Is the new design available yet and if so where can I buy one? Cheers.

 

[SteveC047]

Yeah mate they are available but will take 5weeks as they are made to order.

I can get them through work they cost around £62.12. I have been temted to get one for the Trophy as it comes with the breather pipe already attached, and saves getting a piece of straight Samco for the breather pipe.

Drop me a PM

 

[ClioF1]

62.12 is more than I expected...

Can anyone comment on how good these are compared to the Hillpower?

 

[caymanr26]

far better - is 4 layers thick instead of 2, has an oil resistant layer on the inside which the hill power doesnt. the inside is far smoother/neater = better air flow, plus has the breather all built in.

 

[Fred@BTM]

we've got 4 in stock, team@yozzasport.co.uk

 

[Dubai182]

Tim did my little surprise get sent ok?

 

[ClioF1]

far better - is 4 layers thick instead of 2, has an oil resistant layer on the inside which the hill power doesnt. the inside is far smoother/neater = better air flow, plus has the breather all built in.

Thanks for the info mate!

 

[ClioF1]

All sorted thanks to tim...

AAAAAAAAA++++ will buy again

 

[hkka]

Any pic?

 

[ClioF1]

 

[caymanr26]

I have a yellow one available if any one fancies it - ordered by mistake so ready to go

 

[Meek_racing]

Has anyone else noticed that the top of the breather pipe rubs against the bonnet lining? mine has a small friction burn on it Will need to tweek it about me thinks...

 

[hkka]

Anyone fitted? Would like to know some comments on this.
I know it should be better cos of the inner surface got smoother. But how's the different?? Or just look good

 

[caymanr26]

meek - mine didnt have that problem - what filter have you got - can you angle it lower?

 

[Matt@Stealthsport]

I'm fitting my one soon so I can provide pics if required?

 

[Meek_racing]

Tim - http://www.cliosport.net/forum/showthread.php?t=234952

I'm using the BMC CDA. I think i need the metal bracket on this fella. The boot lining is also hanging a tiny bit low... So lots of vibrasions means that it is rubbing against the hose.

P.S, sorry for the dirty car

 

[Meek_racing]

Hkka - It looks great and sounds jubblies with an induction

 

[Neil G]

Anyone fitted? Would like to know some comments on this.
I know it should be better cos of the inner surface got smoother. But how's the different?? Or just look good

Haven't fitted one but 60 quid is a lot of money for cosmetics

Good s**t though if you have spent loads of money on engine detailing etc

 

[SteveC047]

I have one fitted running the standard air box and K&N panel filter, it does make a difference as the internal bore is smooth so allows the flow of air the run faster with less turbulance.

I doubt that there will be any notable gains, but in theroy it should allow the air to flow better so it cant be a bad thing.

 

[Neil G]

unlikely to make any gains on the dyno though even though it's smoother on the inside than the OE one.

Looks very nice though, just wish it was a little cheaper but I suppose it's cheaper than the Subaru ones which cost over £200

 

[Meek_racing]

It *cough* was a bit cheaper for a few of us think that "special offer" is over now though...

 

[SteveC047]

Ha Special Offer, I just bought mine through work at cost, complained about the fit, and Samco sent me another one. Thats the benefit of working in the performance parts and accesories market.

 

[Lagerlout]

£62!!!? My Maxogen is starting to look ckeap.... one piece silicon elbow with breather pipe included in the kit

 

[springer]

£62!!!? My Maxogen is starting to look ckeap.... one piece silicon elbow with breather pipe included in the kit

Its cost me £230 for BMC CDA,2metres of caf from venair and Samco induction bend.