Search results

Connects2 - CTARNIPOD3 - this is the 40pin connector - if you have a newer model apple device with lightning port you can get an adapter from apple - drop Matt (MTAudio) and see if he keeps these

Sent Matt (MTAudio) a PM and he can sort you out with the correct adapter and patch lead - top guy

Or u cld buy the autoleads cable for like £7 :p

The op's post isnt thtat clear tbh - does he mean he wants just an aux and no radio, or an aux adapter.... If the no radio option it will need to be amped before speakers, if keep radio then will just be an aux cable - id say the post about the amp was clearer than op tbh

Tell that to the copper when he's writing out a fine for what is now classed as dangerous driving over careless driving - its not me you'd have to convince

Run it like a boss to a brodit pro clip with active holder which will charge your device at same time ;) Also if its an ipod/phone - better off just getting a connects2 apple interface so u can control through HU, Mind unless the device is in a holder then its technically illegal to change...

Hen night maybe - but cant see many birds wanting to get in a clio with lights like that [emoji23] - thought u were meaning footwell LEDs - each to their own - mind dnt get caught driving with them on [emoji106]

Well if not the leds and not tbe power supply and not the earth - then surely it can only be the switch? Led strips are not the most complicated

My guess would be bad earth- if pulling down from cig lighter then why not just earth through cig also?

There are 3 parts to the xenon lights - blubs/ ballasts/ ignitors. If the old bulb was smashed then it would have failed for obv reasons, if the replacement bulb is intact - it could be a fuse (both sides are fused independantly) ballast or ignitor. Ballasts can get damaged from water ingress...

F7 or F29 if clio 1*2 iirc

Im expecting a pic of a vibe fastplug

(Also) you need to plug the yellow into the opposite side to where the blue is - as the side its plugged into is unpopulated

The stalk controls are the yellow block, (in simple terms) in your pic you can see a longer plastic lug this should be facing to the outside of the black plastic block, To check: 1. Check that all the pins line up and enter into the yellow plug 2. Is this the connects2 'ctsonylead' you are...

Bottom right on back of hu is a blue socket - plug your patch lead into this : https://www.google.co.uk/search?q=sony+bt3900+rear&client=safari&hl=en&prmd=si&source=lnms&tbm=isch&sa=X&ved=0CAcQ_AUoAmoVChMI04_2y6fZxwIVA7oUCh0nVQFe&biw=320&bih=460#imgrc=-4vKrPAEeti6-M%3A

Try and pull all cabling out- original plug is prob buried deep in dash

Best bet it to get part numbers from the brodit website then fire them into google/amazon

Also what ever you do go pro and get a brodit holder + pro clip - you can even get ones that charge your handset at same time for a bit extra £

Fitted loads of parrot kits before stick the the 9100/9200 as the ck3000 is rubbish, autoleads do io - not much experience with these - only fitted a couple.

as above, whats the make and model of new hu

The extra power depends on what hu u are using some hu's have an option to power through the smb connector - if in doubt just run this to ignition feed, as noted above copper strap is for earthing as the aerial is powered, so a-pillar off is easiest fit

Just put a molex cig lighter behind dash and spur it pff fuse box? Or just run straight from fuse box- dont see any complication as long as you inline fuse

Take it youve already checked rear shocks for leaks?

Sounds like an issue with the adapter, would have a visual check at pins on adapter and check theyre all secure and theirs no damage - connects2 had a good customer service so will replace, Also check the rear of the stero and make sure the pins for the changer arent damaged

All aftermarkets stereos will require stalk control adapter, cheap as chips though - connects2 adapter is plug and play- PM Matt @MTAudio and he can sort you out

Blue iirc, yellow is stalk, not sure what green is

Bit confusing as your complicating things by quoting model numbers, im presuming you are putting the alpine into the boxter? Are you getting 12v on red/yellow when ignition on? And is the earth (black) matched on the iso?

Js cut the plug off and connect the '+' '-' and illumination - 5min job

Another obvious one- but are hu settings for the sub turned on?

When i worked at halford the made to order saxton matts were really good quality - around £40/50 for tailored mats - but can take up to 2wks, else wise when i had my clio the geniune renault sport ones were decent - white piping tho