Search results

*Pegs that go into the airbag slots

Exactly the same thing happened to me. The airbag frame had been bent, so the slots in the dash wouldn't release. My solution was to unplug and unscrew the passenger airbag in situ and bring it out with the dash - super fiddly with a 1/4 wrench but it worked. Then bent the airbag frame back...

Heat gun? Might be able to soften and remove with a plastic tool before going in with anything sharp

I have a Haynes manual, that's pretty useful Not told me to stick it in the bin or plug it into CLIP yet

HTH

Fruity, custom exhaust?

60K in mine and never a single pop or bang, might be worth fixing it before f*cking with it

That's what I was thinking... If MC fluid/pad pressure is the same as before and the pedal progression from the bigger calliper cylinder feels good why mess with it 🤷‍♂️

@stealthstylz have you had chance to change over the master cylinder? I have been running this conversion for a couple months and getting on well with it. Prefer the linear feel so much more. I have 182 MC ready to go in and was wondering how you got on

Would recommend genuine again. Aftermarket split after two years and leaked the gel-bush-fluid stuff inside. Genuine been on their three years and still doing a great job. (assuming its one of these) And for the rear engine mount in principle yes, the bolt hole is offset so as long as you...

From my experience three options: 1. Buy genuine, rubber lasts way longer and stays tougher. I had an aftermarket (maybe Febi) break on me after two years. When braking the engine would shift forward meaning I lost reverse, 1st and 2nd... That was a fun drive back from work 2. Buy a cheap one...

Wow

Thank you for the info, even with the few extra mm on the 280 disc it will be well off then Won't be as easy as using 1mm washers as you did in your TurboRenault write up Thanks again

@Adey. Bit of a revival, going down the route of 307/280mm conversion. I did a test fit today and I wanted to ask if the carrier gap looks about right. I haven't used any spacers here so it would come out another 1-2mm - does this look similar to your twingo set up? I assume the carrier sits...

Done 50K in mine now (78K on the clock) and this rings true. Serviced every 10K, new timing belt and pump when it needs it then given a beating. Drive it like you stole it and it comes alive, as much as it can... I only use 5th for cruising on A-roads and motorway, good pull at 4K but only on...

£100 for you knob to feel good sounds like a bargain HTH

Ruined the bearings on mine with spacers, twice 😅 First replacement was eBay specials that lasted 6-12 months. Second time round I found some higher quality FAG ones. Likely to be the other side, but could be a bad bearing - If you can get the back of the car in the air and freely rotate the...

Fixed mine doing exactly this

Did it with a 6mm 😅

I want to do mine but I have a small speaker sub in the way. Anybody running no seat-spacers and an aftermarket sub that fits under?

I believe they just raise the seat an arbitrary amount. I have seen people recommend swapping them for washers to lower a few mm - or binning them completely as @leeds2592 has suggested

Still on the forum, this is the for sale ad under his user: https://cliosport.net/threads/172-turbo-sold.836783/

When my dogbone went I only had gears 3-5 due to misalignment ☠️ Could have joined a bobsleigh team after I perfected the 5-point-push-turn

Hydrate-80 by Bilt Hamber is the most recommended rust converter/treatment on here if that helps. Ignore me if you know about it!

Part no 6: 7701045041 Cant find any new ones for sale. I would suggest rust treating the old one (if surface rust). Otherwise try finding one at a breakers, they do come up on Ebay every so often if you are willing to wait. PartSouq Link for image and part numbers

Do you have a multimeter to test that the positive live and the accessory live are working as intended in the car? Im pretty sure I had to reverse the connectors on my Sony unit, as in: Red ---> Yellow Yellow ---> Red

Looks like you need and ISO to 16 pin connecter, if @SharpyClio can grab an image for you it should make more sense

I used a strip of window tint on the inside as a sun strip. Cuts down on sun glare while being able to see through it

Jack the car up and stick it on wheel dollies? If its only got the handbrake on you should only need two for the rears