Search results

i would imagine an fk dealer could source the parts a member called john2modified on here should be able to sort you out good luck

^ thats the race car

http://www.k-tecracing.com/show_product.asp?id=1383 here you go! ***but*** yours have koni shocks so could be different again......

.

Re: Inletmanifold at angel-works dunno, 5-10 hp are the average gains..... maybe more if you have a poor cast..... it'll probably feel keener.... but these gains are pretty small in the grand scale of things..... but every little helps..... pm ben r, he is very good, and will reply. i...

i *think* you need 2 more rubber mounts and washers. The bits in the last pic are for the rear shockers, you need a rubber mount and washer (wheel arch side) and the same in the boot.... they sandwhich between the car body. these are the bits under the rubber caps in your boot. Hard to explain...

Re: Inletmanifold at angel-works still get it done, its the best mods per ££££ you can do to these engines. No exhaust or filter will get you the gains the inlets will

Re: Inletmanifold at angel-works i've got it done on my cup, and with a panel filter and groupn ecu, it comfortably passes 182's do it!

i find them all loud!!!! o.e is peacefull

well there is summat wrong if a ctr has had you, there is a dick hair in it.....

don't get gaz coilovers, they are proper pish

....clap**

fcuk the planet i say, we'll be long gone before it explodes/disintergrates :rasp: bloody tree huggers and their emmision regs lol :rolleyes:

not alot you can do matey. Think rage are you get what you pay for. The magnex systems are pretty quiet though

all 172's do this matey :(

look at the one in holt, its on the front, and looks alot more blue/silver (drove past it today!)

get a grp n ecu. Off the shelf mod, good gains, quicker fbw response, and cheap!!!

lol! more mods planned ;)

i'm amending it tommorrow as i now have a standard zorst on it too! (sold the prospeed)

yeah, abit fiddly but not too bad. also has two wires plugged top and botom of the airbag unit, and a red and black for the horn. Remember to disconnect the battery first. ;) steering wheel is held on by a torx bolt, undo this, but not fully, as you need to give the wheel a good YANK (lol)...

mint imo, much better feel than the bus like standard job. That one is a momo race, and in 320mm size (a must) easy to fit, but momo only supply 1 resistor for the air bag light, but you need two 4 ohm jobbies (18p from maplins lol)

i was...... drove some of the 'competetors' CTR... and wasn't that impressed tbh, so keeping it now! fallen back in love with it lol!!!

some new pics of the new addition :approve: what a mod lol, they should have been this size from the factory!

i ground some off the ends, they wouldn't even go in with out the anti squeel shims!!! apparently its common on aftermarket pads

^ did yours not have an r sport? if so why the change mate?!

well thats waste of time then!, i will be buying old school clio's for a while yet then lol!

any good?! :rasp: these were mine (sold them on now) they dont come with centre caps as they are a motorsport wheel, but i beleive you can get them. Make sure your car is low with them on!

i had some daytonas in mine, think they'll be the same subframes as yours, there are 4 10mm silver spacers to where the seats bolt to the frames, i took these out too! proper low then ;) now looking at some trendlines... in black cloth for the cup interior

get a leather momo, mine is a momo race, and it feels superb

good man, i thought there would be no chance in a clio lol!!