Search results

Only some 172s and 182s where its two piece and require the bearing on the back of the block are not usable obviously, unless you fit the bearing too, as the holes are there for it... The other three are definitely interchangeable, as ive got/had sets of all three and have the dimensions. They...

Chris's (480bhp) project thread

Ph1s do run a UCH, just not the newer CANBUS version. The immobiliser and other features that revolve around relays (headlights etc) run through it

Correct. I was just generalizing on aspects where the Ph1 can be lighter than the Ph2

Ph1 has alloy bonnet

Il send you the bill for the amount of times you've lent my jack (you could have bought 10 jacks by now if I charged £10 a time LOL) ;) Oh and the bill for the cylinder head I gave you ;) I'll just to do a Dorkins and not give it you for 8 years.

Well that pic was taken with my 70-200mm @ 200mm when I had it...cropped ever so slightly but nothing much. There is still quite a bit on over winter to practice with (trackdays) if you get bored lol.

Its quite a good place due to it being quite a distance from the track, and you can go further back if needs be. If youve got big-ish zoom 200mm or bigger its easy to drop the shutter speed and get good pics due to the pan being pretty slow

Looks like its after the first corner on 'The Avenue' Ian

Im running the same setup Jonny. DS2500s, HC's, Lines and cheapo Halfrauds 5.1, never had any issues all year they have been faultless...seems odd that yours should be any different

http://www.cliosport.net/forum/showthread.php?t=467847 Post #3...should still work, there are other similar offers that work the same way on there too...just a matter of reading up on them. I renewed at the start of september (for the 2nd year) with no issues

you can get pro for free anyways!

LOL.....IIRC his dad is quicker round the track than him I heard?

You can get pro for free, lots of people ive told too have done without problems also. Its worked for me for 2 years/renewals too. Go onto your photobucket, choose the option to 'get pro for free', then use the 'TrialPay' system they promote. From when I did it, LoveFilm had a 30day free trial...

Finally got them on, looks good! Sort your saggy exhaust too though!

172 Ph2 and 172 Cup will fit 182 only passenger side will, drivers side will not

Re: Mk1 172 Hybrid Track Car Project No not usually, only occasionally. And they are just held on with two screws :)

Re: Mk1 172 Hybrid Track Car Project Early afternoon dry session, with Naith in the car. In front of Whiteley... zG0SoMkspoc And from Whiteleys car... 6D4_l1hhONw Chasing Andyrg down for a few laps... K4Ur0RoDSbQ Dry-ish session with some Meganes... utGrqcCMLg0 And the slippery bits...

Re: Mk1 172 Hybrid Track Car Project Few more pictures from the photographer at the RenaultSport day...

LOL aye, just like the manifold that fell off 3 times, with the latter being halfway round a sighting lap :clown:

Ive offered him my pre-made loom and emulated ECU already too LOL ;)

Compression was down on 2cyl before the day began, lol. It would not hold idle on cold start for around 30 secs...then would struggle too. Used to smoke like anything (had a fresh cyl head on it), lol. Think it ran low on oil, temp shot up and there it went....good riddance I guess lol.

Bottom end went nick!

Very good vids :)

All the gear......No idea.

.

Just needs a bigger rubber on the mount to stop it moving over hopefully Yeah that was 1.35

Yeah, its the ghey center section, too big for the tunnel where it goes over the rear axle, so it rattles on the chassis :dead:

"Brictek at its finest..." you say at the end, LOL. The rattling and knocking is the silly center section!

K4Ur0RoDSbQ