Search results

Be 5k off the pedal when I have an air leak from the inlet. :wink: Will let you know though, but i'm not going to the limiter from cold haha.

Are you doubting my skillz blud?

I'll check tomorrow after i've done the plugs.

I might do, it considerably better than a generic 98ron map? I'm told mines been 'remapped' but all PO's lie. Havn't actually looked to see whether I have a rev limiter at 7.6k or not though.

Bilsteins, 2118's, mapping, polybush/black allround, PMS Topmount/brace, ARB, Bumper/Bonnet respray. Will probably just shove a 98ron map on it next as all the other maintenance is pretty much out the way. Can't wait for the mods. Expect lots of whatsapp updates.

Might be the guard which is similar to on the 1*2's? Can you not get to it to pull it out?

Everything I want to do for my car is so expensive...

Looks great mate!

98 ron map is the one with the rstuner. The overrun map is another that's used with the rstuner, but it's s**t.

Wasn't it recommended from factory to run higher octane?

Is that front grill standard? Lets down the front end really! Other than that it looks stunning. Subbed.

Some people experience misfiring or lumpy running with the cheaper fuel. IMHO when you account for the points from shell vpower, even though it's like 6p more a litre, you're probably only spending about the same as if you put in the cheap stuff. Triple points on v-power nitro+ at the minute...

Loving the timelapse edit Mark!

I contacted pretty much every company and proplates were the only ones to actually help out with making a smaller plate (besides fancyplates). For the standard sized rear completely plain it's £9.99, then a smaller 520x85 front plate it's £10.99. Not sure on postage but I don't think it's much...

Bumper is so simple. Pull out from the sides, 2 top bolts, 2 bottom undertray bolts and it's off. Very cheap! Shame it's recorded though.

Looks nice, new bonnet and you'll be grand. Hope there's no damage underneath though. Where in leeds you from mate? And how much you pay for the RB out of interest?

Looking good with the carbon bonnet Dave. Use Proplates if you're wanting some clean plates. They'll do 520x85 too if that's what you're wanting. Cheap as chips. https://proplates.co.uk/ You need to email them though.

It's a 1.2, probably wasn't even worth getting insurance involved over it. New bonnet/ windscreen and leave the dent in the roof.

Davyy prefers the smash it with a hammer and throw money at it approach.

I've got the original recall letters (about 4, renault got needy) and the PO had the latch actually replaced as it was shown as not functioning correctly. Just keep them greased up and moving and it'll be grand.

It'll be the light itself that's knackered. They let water in and then die. I need a new one now, as all the plastic of the light itself has gone brittle with it's age, although my DIY LED strip is still going strong. You can get in from the front with a small flathead screwdriver wrapped...

Given the car a thorough clean the past few days making the most of this sun. It had gotten filthy inside, so I vacuumed and cleaned all panels, seats, doorcards etc to get it spotless again. The seats need debobbling which i'll do when home, and also the bolsters could do with a little...

Lovely BG mate! It's like i'm seeing my own car sometimes haha. What's next?

Proof of cams? Everyone says the car has cams..

Instagram follow4follow?

Raise it a little and it'll handle better, all IMHO. And yeah, what mods?

Are they not worth it for the road?

What springs it on mate? Or it on coilies? It's very low... Too low really! Ruins the handling. Needs spacers or different ET wheels to fill the arches too if you intend on leaving it like that. Looks nice though, what's the specs?

Wish it showed it without to really show the full extent of movement. Crazy how an ARB, running along the similar shape and being much thinner can stiffen it up so much.

He's busy trying to change his name to RenaultLaid