Search results

Bought them premade on specialtec ;)

Why are comparing proper 3D to the 3DS? It's a bit mongish.. You need glasses for any kind of decent depth. End of story

Re: Ollie's Silver Cup - JMS RS2/428s/Wilwood/2118 Don't really understand why running 428s will be a problem? Seems daft. I saw you today on the m1 about to join the m40 bobbing along in the middle lane lol.

Very tidy that! Like it a lot As said lose the filter and opt for a back plate and dome solution if possible.. Don't opt for universal socks either they strangle mid range torque massively and make the car flat as a pancake!

New PCI cables in.. Off on hol now so will finish up next week. laters

Powerflow normally put their branding on the tip. In all fairness they're not that bad either. THAT looks like a nasty system

As above, wheel and forcefeed back is spot on but the pedals are too light and flimsy. Always felt like I was going to break them.

Will believe it when I see it. LG's Stereoscopic monitor isn't all that impressive - you'd think they would try and perfect that first! Plus the depth will be pants!

Re: Dog b****cks Xigmatec case Covers the entire block including all memory modules. I mean they do run a whole lot cooler, but they have such a high tolerance anyway that's not really a problem (plus GPU overclocking is basically like trying to ice skate up a hill). It's when the fans start...

never used anything but the elf stuff tbh. Car ran flawlessly

could work REALLY well if done right..

not bad, think it was 45 quid from the stealers last time I checked. (That was with filter and washer now I come to think of it, duh)

This game is going to keep me occupied for YONKS. I hope it's not delayed :(

That looks spanking. Ph1s look epic in white

Do you think it'll be wrapped? giggles

what about a big kiss? :D

aye just spotted the thread - you're mental, Andy If I didn't have my ph1 I'd snap that off you. It's a proper toy. KEEP IT!

that whole article is pure b****cks, if they do a Williams I doubt it will be in the life span of the 200 IMO. Could be wrong though

yeah was looking at those, maybe in a month or two.. I normally chop out and sell up for next gen though, so not sure if it's worth it. Not that 580GTX SLi isn't overkill enough already. lol

the watercooling setup is extremely quiet, the pump is fairly silent - all fans are hooked up to the digital controller in the front bay so speed can be toggled like Currently with the CPU clocked @ 4.3 it's running at steady 36c idle and hits 52c under load..makes the video cards seem more...

Harsh lol ^ Some nice shots there

uh... ok

I thought it looked a bit different.. Still that would look pimpin'!

Re: Dog b****cks Xigmatec case Finshed putting it together just now. Compression fittings are loads better... just a few more braiding/tidy bits coming and it's done

nice car too :)

aye, well thats the plan eventually but I'm not sure about splashing out on 580 water-blocks at this stage, might wait! Can't really afford it at the moment. I've bought loads of white sleeving and cable tidies so it's all perfect.. or at least near as lol

lol cheers. I actually went with these as they were fairly cheap http://www.scan.co.uk/products/ek-psc-fitting-13mm-g1-4-black

Re: Misfire issue which is solved by a restart - spark plugs, leads, coilpack 6 month as above, even if the camcover looks relatively clean, check the VVT solenoid isn't leaking as they have a tendency to do so and put oil down well #4 Caused my old lump to misfire intermittently

Re: Dog b****cks Xigmatec case I went for the Phobya block, will see how it goes - I had the XSPC Delta 3 before but I didn't think it was all that good tbh. Should be all back together and done by tomorrow night hopefully. Also this is the first time I've used compression fittings so will...