Search results

15inch dynamiques lowered 60mm.

Personnally id leave out the srp and the egp. Use the carlack on its own then put the wax on top. If you wanted to use it all then it would go: carlack, srp, egp, wax. I havent used that wax though so i am not sure how well it would bond to the egp. Should be oright though. Have you...

Get some second skin or dynamat extreme and do the tailgate and boot floor. As many layers as you can afford:clown:

By upgrading just the speakers you will have no noticable difference in sound. By upgrading the headunit it will sound better with the stock speakers. Headunit and speakers will sound decent but will still distort at higher volumes and will lack any real oomph. Next step is to do headunit...

Will be good to see it go to a club member and see more progress.

Ive got an alpine headunit with the alpine ipod cable and it doesnt charge it. Even my charger at home didnt work i had to buy a new one.

My mates clio. In Purley this is. He had already wiped a huge chunk off the bonnet too.

I done the same just before new years eve in my saxo. Wishbone was bent like a farking bannana. Needed a new alloy,tyre,wishbone and stabiliser rods.

Hasnt snowed by me since about 4pm. I hope it isn't all gone by tomrrow:(

I hope there is more snow later/ tonight! There is a micra on my driveway with 12 inches on it atleast already. I will own you all:evil: Looks like our area got hit the worst rhino!

Speed bumps and pot holes all round my way. 60mm was fine it scrubbed a few times and the exhaust pinged on some speed bumps, but for the looks it was worth it. Just have to go carefull and go up one wheel on the sleeping police man ones.

Becker do some good headuntis which look pretty plain. In my old car i had a sony xplod headunit and it looked ok had good features but the quality of the signal it was sending to the amp was crap. Can you get clipping from a headunit signal? When i fitted this it was a massive difference...

Welcome to CS, how old are you? x

Re: Snowd in Contest!! No clios

Did you put them in?:cool:

30? You're just too sensible;)

Lol, Lubbed up ofcourse;)

Did you spray them with the centre cap on? Will look a hell of a lot better once its lowered. Please say you are going atleast 60mm?

Hats off to you mate, "meet videos" FTW:)

This is what i have mate: Any sort of body filler will work though. You can get it in halfords or a motor factors place. It comes with a hardener in a seperate tube and you mix it up then slap it on and it will set like concrete. I would suggest putting it on with a credit card or simaler...

Get a little plate spot welded behind it. Then filler.

ROFL at string cut up a wire coat hanger and feed it through. tape your cable to it and pull it through. Lay on your back and you will see the bonnet release cable go from the pull switch up and through the firewall. It is behind the loom a bit next to a load of cables.

Carbon glasses so everything you look at will be carbon fibre.:clown:

Crap font on the number plates. Looks quite nice though. Get some smoked side repeaters on it!

apc and a brush as said. when i used to give my clio on a proper detail i used to take them of to polish behind them.

i got 4awg through mine no problem. slit a hole in it with a stanley knife. vaseline up the cable and poke it through.

i thought mine was platinum silver but when i checked the paint cos it was gris boreal not 100% on the paint cos 633? ring renault and give them your reg and they will tell you the paint code for you.

nice mate. lower it and leave it as it is. save your money for your next car.

Yeh thats what i thought. Why you have to wait a few seconds on ignition on the older cars.

i dont do it. just get in there with some degreaser and a brush then get a small spray bottle with water in it. spray, agitate, spray water then wipe with a microfibre.