Search results

Thanks, Iv chased them again. They were quick to respond to emails within the hour before I bought the software & cable and since the £250 purchase its 6 days between emails. I made sure to make this known to them. I wasn't sure if the licence was now incorporated within the cable or something...

Looking for some help from those of you familiar with the Gen90 ECU and the conundrum of trying to connect to it. Purchased the ecu 2nd hand, installed into my Ph1 after the pin swap and car starts & runs. Purchased a cable and software licence from ktec, received jist a cable and no dongle...

Another thanks to @NorthloopCup & @barnesautos as just used the info above to repin a gen90 for my Ph1 with no drama's and also the additional info for the fuel pump pin swap also. I was an idiot though and didnt realise until half way through that I reswapped a few pins rather than use the...

Also to add, googling the numbers from them returns very little matches which made me wary

Does anyone know the part number from 197 injectors? My jenvey bodies came with a jenvey fuel rail and apparently 197 injectors that have been flow tested. 2 of the injectors have 255/05 etched on them 2 have 235/05. Bit wary of running them if unknown and mismatched

Iv got both sets of halfords, the orange 2T ones and also some black ones with the 'ratchet' function. Much prefer the pad on the orange ones and sits fine on the clio chassis rails. Apart from my integra dc2 that had front and rear central jack points, the clio is one of the best. Plenty space...

I have the sealey premier ones. Angled head & reversible. Also had good support from Sealey on replacing defective parts under warranty with no quibble and posted out no problem with both these and also impact hex bits. All broken through my fault. Im sure their available cheaper via other...

Cheers, I'll have to get a suitable laptop to get it loaded onto as only got a macbook atm. It was already mapped by chris @ efi when it was in the previous car however have since added cams. Plan was just to get it running and then trailer it to a local mapper to get it setup properly. I didn't...

Ecu powers up and fan starts and then stops. Blue power light is on alongwith General 1 (red) and Tx flashing yellow on both serial in & out What software is needed to read the adaptronics ecu? Haven't been into it to check anything

Forgot to add, both engine loom earths checked & also gearbox to chassis earth checked

Just installed wiring loom and adaptronics ecu for running ITB's. Car cranks but won't fire, fuel pump isn't priming on ignition or when cranking as all fuel lines are bone dry. Immobiliser light goes out after a few seconds Engine bay fuses & relays have been checked & cleaned Fuel pump...

Perfect, cheers for the info. I had ordered one of these months ago, yet to delve into the footwell as cars hard against the garage wall just now until I move it for access so unsure if its suitable. I already have the jenvey cable with suitable nipple so will use these alongwith what you...

What setup is everyone using for a throttle cable when running ITB's? I have a Ph1 so cable throttle already however id rather fit a readily available cable so I ordered a Jenvey cable. Also got a few linkage's so hopefully can mount it to the pedal ok. Does it need to run in the standard...

Much better trying to get the seal tool for anyone wanting to do it, yes you can use a piece of coke bottle etc to help it onto the shaft but the most important part of the tool is that it sets the depth correctly.

Was that a megane oil pump you installed or just the clio dci one? I recently installed a dci one from PMS on my ph1 172 and didnt notice any clearance issues.

Pretty sure they are manufactured by Norbar so its a no brainer really

The halford's ones are identical to Norbar ones, and as said above try get one on trade card or join the motoring club and try get a money off voucher. I have the below halfords ones and covers most things from engine components to wheel bolts. They do a range of 4, I went for 2nd lowest & 2nd...

Top mounts was another sore point with our regs, as some were running solid top mounts such as PMS with their strut brace and that was a no no aswell. I proper 4 wheel laser alignment geo setup will do it the world of good aswell when you get your B14's on. I would also consider fitting cup...

Cheers, may just revert back down that route. No progress for next 10 days while Im away You go to all the effort to renew 'one use' bolts / nuts where required and you end up having to back them off again to redo timing 😂

Be careful if considering the roll centre kit, as it has rose joints which will affect the class you are in for hills / sprints. Im in A2 in Scotland, road going cars so allowed quite a few mods however blue book states that bushing material can be uprated for poly etc however no rose joints...

Spoke to Nick as I was messaging about the tensioner issues. The provide a cap screw for this application as the countersink on the cams swallows up some of the length. Link below incase anyone else comes across this or for future searching. Cheers for the info struggler, definately looks alot...

Photos for reference

Mulled this over for a few days and thought must be ok as even if there was a deeper thread in the cat cams, it wouldn't matter as would still bottom out on the non - threaded shoulder on the stud Torqued the exhaust cam and low and behold, didnt get enough 'stretch' to gain a full nut. Have...

Running a 'performance' car, fuel prices are going to be the least of your worries and you can't neglect some of the costs, whether its fuel or maintenance. With regards to fuel consumption, these can be fairly economical (for what they are) when driven sensibly / steady runs

Yeah I did check and see if they had anything but just the full kit as you say. No real rusj, just had my milestone was getting it finished off so once Im home I would then get the engine back in. Frustrating but Id rather it was right

Unfortunately dingbro had no stock in the company so got a gates one coming from autodoc. Unfortunately Im away Tuesday for 2 weeks so it will be burning away in the back of my head for the meantime

Anyone came across this issue with fitting a new exhaust cam stud on cat cams? With the nut just nipped up (not torqued) Im not getting a full nut and I doubt I would gain 2 - 3 threads when torquing. Genuine new stud used and wound in until bottomed out on the shoulder. Bit wary to build it...

Im going to have the bore of the pulleys worn out the amount of rotating the belt Iv done, still only getting the below. Stuck on the old tensioner, and can get the notches to line up on it. Think I'll order another new tensioner as I just don't trust this one now

I can get the marks near by manipulating the belt as the tensioner approaches the marks but still, from guides it seems it should be a straightforward process to align the marks. Everything moves freely with the tensioner, all pulleys flush etc etc

Manual states about not moving the tensioner itself anti clockwise when setting it Iv rotated it endless amount of times to try and even out the belt tension, and still the marks are stopping just short