Search results

I may just do the same actually. Order a trophy centre cap and get them to match it...

Hi all, I have a set of 172 cup turinis which I fancy getting refurbed for getting my RB182 out of the garage and MOT'd soon. Can't quite make up my mind on colour. Thinking either a fairly light coloured grey or silver? Also, my car is totally standard and so is at standard cup suspension...

My issue was valve clearances set too tight. I’d set them for the non grooved cam. I found the correct clearances for the grooved cam d4f and it’s been running fine since. Sent from my iPhone using Tapatalk

Hi all, I'm need to do the timing belt on my 2.5 dci master. I have the locking tools etc but would like a renault workshop manual for this. Would be must appreciated if any of you could share a workshop manual for anything with a 2.2/2.5dci engine or laguna etc. Thanks, Rick

Hi all, My 2009 1.2 16v Clio was running fine. I then checked and adjusted the valve clearances to 0.10mm inlet and 0.20 exhaust. First start up after this it was misfiring at idle. No fault codes. Engine will stall if held on slight throttle. Revs initially lift, dip and then stalls. Engine...

Hi all, My brothers 2009 1.2 16v Clio had been sat for 18 months. Started up as if it was running the day before. Drove it up home and check injection appeared. Clip is showing it as a throttle body fault. It’s intermittent so it sometimes isn’t present when the engine is started. Live data...

I had to do that to enter the serial number. Generally isnt an issue when using clip except when trying to change configurations.

Sorted. I copied the probes files from my netbook and its working fine, When I plug it into an older car like the clio, and it wants to start an old version of clip for diagnosis, it fails sighting a .dll fault.

I was using Clip on this laptop through VMware running W10 32bit. It was too slow so I just done a clean install of 32bit on it as I got a new laptop. The netbook is windows 10 32 bit and it works no issue. Problem is the screen is so small there’s parts of Clip I can’t see. Sent from my...

Hi all, I installed V203 on my W10 32 bit laptop. I have the china clone RLT2002 probe. Works fine and have been using on my old x86 Dell netbook for a while on V193. Drivers seem to be installed ok but I cannot find the sensor when I open clip. I changed the probes files in config for the my...

For me I changed the cruise control buttons on the steering wheel and it fixed my issue. I also had intermittent cruise control not turning on at all before I changed these. Speed limiter was turning on I think. My brake switch was fine. Sent from my iPhone using Tapatalk

Is it not push on metal clips that go onto these? Sent from my iPhone using Tapatalk

I havent replaced anything yet. I was still able to use cruise just by pressing the wrong buttons. Now, the green light won't come up on the dash and cruise won't activate. I will replace buttons and play with the brake switch. Think I remember something on here about taking apart and bending...

How do you do this? I’ve another problem now. When I press the cruise control button the green dial will not come up on the dash. Speed limiter works fine.

I replaced the wheel with a non melted wheel. The cruise control was messing about before this but not as bad. Might remove the airbag and have a look at these. Sent from my iPhone using Tapatalk

Could the brake pedal switch cause all this? What do you mean aftermarket bracket? Sent from my iPhone using Tapatalk

Evening all, My 182 has always had a bit of an odd problem with the cruise control. It and the speed limiter work fine but the buttons don’t do what they should. Currently speed up either cancels or does speed up, depends on what way it’s pressed, speed down always speeds up, the cancel button...

This is class. Feel free to reminisce some more. The respray seems to be on drivers side and roof? I might head to the RS day at Silverstone this year. If I do, you should come and see it? Sent from my iPhone using Tapatalk

This your Megane GT also? Sent from my iPhone using Tapatalk

Right guys, Been a day or two since I posted. In the last few months the car hasn’t done much but about 3 months ago I found myself whipping the rear door cards off to find some rust. So I treated that. It was mostly surface with the actual sills still solid. Problem was blocked drains...

You have a point. Face ID can be a bit terrible at times. Fingerprint is much better. And I was on the same boat. My 6s was great, still fast etc but the battery was dire. Sent from my iPhone using Tapatalk

I wouldn’t go for an 8. What about a second hand iPhone X? Sent from my iPhone using Tapatalk

Hi all, I was in the daily 1.2 mk2 today and went to put down my drivers window and all I heard was bang, the window continued to go down at the front but stayed high at the rear which then led to the window falling out of its runner in the rear of the door and totally out of the window frame...

I assume these are like the mk2 Clio where oil pressure isn’t monitored below 2200 rpm. Suggest if you checked the oil level etc to try the oil pressure switch. Sent from my iPhone using Tapatalk

Passenger side. I ended up not replacing it and just adjusted the handbrake as best I could. It passed MOT. The mot was that evening, so I didn’t want to chance the first line cable not working and missing out on the mot. Sent from my iPhone using Tapatalk

I got the drivers side one back in September no issues. Sent from my iPhone using Tapatalk

This first line LHS measures 1400mm total length. Sent from my iPhone using Tapatalk

They have discontinued the 182 handbrake cables. This is my point. I got a first line one today. Will it not fit? Sent from my iPhone using Tapatalk

Hi, So in August I ordered and fitted a new handbrake cable for my 182, no issues. Today I tried ordering a cable for the left side as there is now too great an imbalance and was told it is now listed as NLA. So I’ve had to order a first line part from my local motor factors. Not ideal as I...

Hi, My brother has a 2009 1.2 16v Clio. When he got it I noticed when engaging reverse the revs would drop and it’s like clutch was dragging, it’s like it’s trying to slightly move back but doesn’t. I then changed the gearbox oil with elf and it cured it. This was at 58k. The car is now at...