Search results

Its been a good several years I suspect since my 182 has been 'plugged in' and given a proper tune or system check by a Renault service centre. Is there much likely to be gained from this, or would I be better off putting the money towards an RS Tuner and doing it myself along with the...

Hi there, I am in the UK for work and looking at bringing back a Whiteline ARB for a 182 and some other goodies back with me to NZ. Does anyone have a close idea of the length and weight of this item so I can check I can get it back okay as checked luggage. Thanks !!

I'm hoping to be able to get an exhaust specalist to modify this Mountune Milltek muffler from a Ford Focus XR5 to fit my 182. Dimensions are - 550mm long, 300mm wide, 150mm deep, 70mm inlet, 50mm outlets, 100mm tip diameter The tips are quite large, but I might be able to utilise them also...

Would be a custom job using two mufflers a bit like this - http://www.borla.com/products/proxs_muffler_part__400481.html ...and then some tips. They have an offset inlet and centre outlet. Would it work ? Getting some of the more mainstream aftermarket exhausts into NZ is expensive, so looking...

I have factory seats and steering wheel. Does this guide also apply to my problem, or should I be looking elsewhere ? http://www.cliosport.net/forum/showthread.php?630252-GUIDE-Complete-Guide-to-SERV-Airbag-Light-removal-Aftermarket-Seats-Wheel

Does anyone make a one piece silicon hose to do a DIY induction kit along the lines of the KTec system. Or do you need to buy the Samco 90deg bend and then add on a metal piece down and around in front of the battery ?

My 182 has a K&N Apollo air filter - came like that when I bought it ( have original airbox also). It has a cold air feed, that appears to plumb back into an original plastic pipe that sits down below the passenger side headlight. Do I need that there, or can I do a better job on the cold air...

I recently used a Rug Doctor ( semi-wet vacumn) to clean all my upholstery. The next day the drivers side indicators start fading away after a few seconds, and I notice I have also lost my spotlights/foglamps. Seems too much of a coincidence..... is there some wiring somewhere that may have got...

Hey there, My 182 has 170,000kms on the clock. Want to freshen it up a bit and get it handling like it did when it left the factory :-) Have allready done Solid engine mounts Powerflex bushes - dogbone, front wishbones and front anti roll bar. Running Eibach Sportlines and planning soon to...

My 182 has had both its rear struts replaced with Boge Turbos ( which I think is the correct shock ?) recently by its previous owner. However it seems very wallowy in the rear. Without much effort I can move the back of the car up and down very easily through a decent amount of suspension...

Car has standard exhaust but the tail pipes hang too low and poke out to far, any tips on what could be causing this ? I am thinking of upgrading soon to an aftermarket system, so if I need to replace any engine/exhaust mounts then I want to do it all in one hit. Thanks !

Hi, As per title....looking at some TE37's in this size. Car is standard height at the moment, but in the future also considering some Eibach Sportlines Any advice welcomed, thanks !

I am loosing coolant in my 182. Its intermitant, but sometimes I will return to the car to see a small puddle underneath just forward of the front drivers side axle and a slow drip. I am also constantly topping it up with water/coolant. Worse case scenario.... if it is a leaky waterpump...

Hi guys - my name is Phil and here is my car :-)I live in NZ Standard apart from a K&N typhoon intake and the 16" TSW's. Plans for the future when I have the $$ are Eibach Sportlines, Milltek exhaust and some Superleggera's if I can find some in NZ in 16" and 4x100 ( they are pretty rare...

Hi guys, First post for me actually, new member from NZ with a 182. Looking for a guide for changing the plugs. Bit of a novice with mechanical minded stuff. Did an oil change on my car yesterday, took a while but all went well. Hoping I might be able to do the plugs also if I can find a good...