Car is going on rollers today!!

[Ryan k]

What do people think i will get?

 

[TeZ]

i reckon 175 BHP

 

[Ryan k]

i reckon 175 BHP

Dont 182 give 179 normally lol

 

[TeZ]

yes but i bet it isnt

 

[ben_p]

168

 

[Ryan k]

Lol best be over 170

 

[MRBILLYUK]

Is it standard ? You could be looking at anywhere between 170 - 180 , maybe even a little less like Ben_p says .Seems like the power varies alot from car to car .

 

[TeZ]

youll be lucky. how old is she?

and as said, depends if it was built after T or lunch or after a PAY rise LMAO

 

[Ryan k]

youll be lucky. how old is she?

2004

 

[Ryan k]

Is it standard ? You could be looking at anywhere between 170 - 180 , maybe even a little less like Ben_p says .Seems like the power varies alot from car to car .

Magnex exhaust

 

[TeZ]

Magnex, well it will sound fast at least.

 

[Ryan k]

Magnex, well it will sound fast at least.

Lol u want a slap :rasp:

 

[TeZ]

heheheehe



No, just being realistic








slap me you naughty boy.

 

[Ryan k]

Lol

 

[avstar1]

More importantly, what are the rollers? dyno dynamics???

 

[Ryan k]

A rolling road

 

[Cookie]

A rolling road

Yes but which one?

 

[Rob's172]

i'd say 178.7bhp how much is it if u dont mind me askin! i want to get mind done

 

[MarkM]

Ive had my car done 3 times

205bhp @ mass
194bhp @ Northampton Motorsport
187bhp @ Torque of the Devil (dyno dynamics)

NOTE: The dyno dynamics run was the most recent with the car in the highest state of tune and 'feeling' the fastest.

 

[Dan 172]

I would say around the 175bhp mark, but it all depends on the rollers really to compare.

I went to Westec in Newport, using Dastek Rollers.

My 172 produced 167.6bhp on the first run and 170.2bhp on the second, so I'm quite chuffed with that as I only changed the air filter for a itg panel filter.

Two Curpa R leon's were there on the day including my mates, they both made 222.*bhp so the rollers seemed about right to me.

 

[makavelli]

it could be anything depending on the make of rollers and depending how generous the guy operating the rollers is lol

realisticly you are looking at anything from 165-180 but if its a gay assed rolling road they will 'claim' its anywhere from 182 upwards lol

 

[lasbazrre]

RSTuninnig roller's 165-175!

leon

 

[ChrisR]

I'll echo the 165ish comments, but as said depends on the RR really as some do seem to read high.

 

[Gumby]

Tyre pressures affect the reading too...

 

[deviltronics]

so what was the reading?

i reckon 170-ish

 

[kully]

around the 175 mark imo

 

[tomhunt85]

I went on at Teg Sport in Carnforth, they were putting standard Scoobys on the rollers and making factory power within 2-3bhp and mine came out at 171.7bhp and 156lb/ft.

Thats with just a Viper btw.

 

[Ryan k]

Went on them got a video too will post up in a bit. It cost me £35 and came out at 175.9 bhp

 

[makavelli]

Went on them got a video too will post up in a bit. It cost me £35 and came out at 175.9 bhp

where did u go ryan? and what make were the rollers?

 

[Ryan k]

Dunno the make but it was mikanics in congleton.

 

[makavelli]

Dunno the make but it was mikanics in congleton.

was it 35 quid for one run?

i was weighing them up a while ago but when i saw their website the rollers looked like sunsystems which are poop, the reading you got sounds pretty accurate tho so they may be running a better setup since i last looked

you know anyone down there? im tempted to have a go as leeds is a long drive for rstuning compared to congy

 

[Ryan k]

he did 5 runs to see if it was correct and 3 of 5 came to 175.9 lol he said he calibrates them regally. i recommend them.
Don't know of anywhere else mate sorry

 

[makavelli]

he did 5 runs to see if it was correct and 3 of 5 came to 175.9 lol he said he calibrates them regally. i recommend them.
Don't know of anywhere else mate sorry

so he did 5 runs for 35 quid or was it 35 quid a run?

i was just checking weather he did it cheap mates rates for you or whether thats the standard price ?

andy

 

[Ryan k]

Nope standard price lol £35 for as meny runs as he likes lol he did 5 for me only £35 no more lol

 

[makavelli]

cool

when did you have it done? ie time of day, was it yesterday?

did you run it with the open air filter and magnex cat back?

would be good to put a few different 182's on there with different mods to find out what mods give what gains

 

[rustybolt]

Pauls rollers are better, Dyno Dynamics seem to more accurate.

 

[Ryan k]

cool

when did you have it done? ie time of day, was it yesterday?

did you run it with the open air filter and magnex cat back?

would be good to put a few different 182's on there with different mods to find out what mods give what gains

Ye i had k&n on and magnex had it done at half 12 yesterday

 

[makavelli]

Pauls rollers are better, Dyno Dynamics seem to more accurate.

yea matey im not doubting that but leeds is a 100mile+ journey for me and mikeanics is about 1/2 a mile away lol

i may do both and see what the readings are

 

[Ryan k]

Pauls rollers are better, Dyno Dynamics seem to more accurate.

I no a few people that have been to mikanics and then gone others an got same results