Ph1 side skirt mounting points

[gudger12345]

Hello all,
Does anyone have the dimension for where the side skirt plastic are mounted to the sill. Pot rivet hole locations ideally.
I have had new sills fitted to my ph1, i took measurements of the distance between each hole on the original sills but didn't take note of how high up the sill they were mounted/ drilled.
Also if anyone has a link to the rivets that would be great.
Thanks

 

[Jaeclio]

Hey Gudger

Is it just the height of the rivet holes on the sill you're after? Cars in the bodyshop atm, but happily measure them up when it's back this weekend if no1 else comes through for you before hand mate

 

[gudger12345]

Hey Gudger

Is it just the height of the rivet holes on the sill you're after? Cars in the bodyshop atm, but happily measure them up when it's back this weekend if no1 else comes through for you before hand mate

That would be amazing.
I need the height of each hole and the location of each hole please
Thanks i really appreciate it.

 

[Jaeclio]

That would be amazing.
I need the height of each hole and the location of each hole please
Thanks i really appreciate it.

It's on my list of things to do this weekend brother, report back soon

 

[Louis]

Put m5 rivnuts in whilst you're there IMHO

 

[gudger12345]

Put m5 rivnuts in whilst you're there IMHO

That was the plan mate
just want to get it right first time before i cavity wax the rear.

 

[Mr Underhill]

Also if anyone has a link to the rivets that would be great.

Rivet info (RIVET G48 x 16 ALU) - Part number 7703072047

https://www.accu.co.uk/blind-dome-rivets/646674-HRD-4-8-16-AZ?

 

[Jaeclio]

Hey @gudger12345, got these this weekend.. whilst doing it it dawned on my that you might be after the brackets that sit above the sill.. in which case, I can still get for you but will be a few weeks when I pull mine off - sorry!

Couldn't see any holes in the sill on the picture you posted above so proceeded to get these anyway!

The height of the first and last rivet hole were up 1.5cm up from the bottom of the sill, the middle 3 holes were up 1 cm.. and the bottom of the sill and sideskirt itself were basically flush on those middle 3.

 

[gudger12345]

Thanks for the information.
Unfortunately i need the locations of the plastic mounting points to then drill the holes to rivet/ riv nut the mounting points onto the car as i had new sills fitted which do not come pre drilled.

 

[mintno1]

Thanks for the information.
Unfortunately i need the locations of the plastic mounting points to then drill the holes to rivet/ riv nut the mounting points onto the car as i had new sills fitted which do not come pre drilled.

I should be able to get these for you, still have the titanium shell here, when I am next in the garage will have a look and get some measurements for you

 

[gudger12345]

I should be able to get these for you, still have the titanium shell here, when I am next in the garage will have a look and get some measurements for you

Hero
Location on the actual sill and the spacing between please

 

[Jaeclio]

Sweet, hopefully Mintno can grab them for you.. if not i'll do it when I pull the skirts off mate but won't be for a few weeks I reckon

 

[gudger12345]

 

[mintno1]

See how these compare as far as I am aware factory sill on my shell, all measurements in mm, to centre of holes. Measurement from outer door jam lip approx. 40mm down and measurement from bottom of sill I held a piece of wood from the bottom of the sill so I could measure flat rather than following the curve of the sill. Also you can see in the pic my black plastic mounts the hole isn't in the middle, hopefully all makes sense but any questions or if you need anything else just shout Cheers Gareth

 

[gudger12345]

See how these compare as far as I am aware factory sill on my shell, all measurements in mm, to centre of holes. Measurement from outer door jam lip approx. 40mm down and measurement from bottom of sill I held a piece of wood from the bottom of the sill so I could measure flat rather than following the curve of the sill. Also you can see in the pic my black plastic mounts the hole isn't in the middle, hopefully all makes sense but any questions or if you need anything else just shout Cheers Gareth

Your measurements are very close mate
Thanks for the information and taking the time to get the dimensions for me

 

[mintno1]

Your measurements are very close mate
Thanks for the information and taking the time to get the dimensions for me

No problems whatsover there was obviously a little leeway from factory