ClioSport.net
Register a free account today to become a member!
Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
-
When you purchase through links on our site, we may earn an affiliate commission. Read more here.
Show me your Harnesses!
- Thread starter MadUsa1
- Start date
that's a nice start, cool harnesses.
Which holes are you using at the back? How do you know they will hold? Is the angle ok?
What about the lap straps, are they mounted to the seat subframe? Closeup photos of the mounting eyes would be awesome!
I have a set of harnesses arriving shortly, but can't decide where best to mount them.
Which holes are you using at the back? How do you know they will hold? Is the angle ok?
What about the lap straps, are they mounted to the seat subframe? Closeup photos of the mounting eyes would be awesome!
I have a set of harnesses arriving shortly, but can't decide where best to mount them.
182 Cup
No pics of the mountings as I'm at work, but it's essesntially the same as above, but not crossed over. A roll cage is on the way with a harness bar to improve the angle from the seat. If it hasn't been done by this evening by someone else I'll sort some closer shots and go into more detail.
Mark Fish fitted my harnesses and bolted/welded in the eyelets.
I'll see if i've got any close ups and post 'em up
Clio Trophy/Boxster
R2TR
Here's mine Sabelt 3"
AWESOME... Where you get them . I'm 90% there the ones i'm after. 140£ each from Dwmon Tweeks?
Blue or black.... hummm..
182 Cup
Right, on mine all holes bar two were already available to use after removing the interior trim.
The holes in the pic below were where the (I think) pre-tensioners were mounted and were the right thread for the eyelets.
These two handy threaded holes were also ready for use...
Only hole that needed to be made and a plate put under it was on the door side of the seats...
The holes in the pic below were where the (I think) pre-tensioners were mounted and were the right thread for the eyelets.
These two handy threaded holes were also ready for use...
Only hole that needed to be made and a plate put under it was on the door side of the seats...
Great post inferno, very useful. Looks like the rear holes are from the rear seat belts, so they should be just fine. On the door side I'm using the oe seat belt guide hole - any reason you didn't use this?
The two holes on the other side of the seat look like a great find - the eyelets just thread right in? are you confident they'll hold? The seatbelt pretensioners were mounted to the seat frames weren't they?
The two holes on the other side of the seat look like a great find - the eyelets just thread right in? are you confident they'll hold? The seatbelt pretensioners were mounted to the seat frames weren't they?
182 Cup
The door side mounts were done by Mark Fish, unfotunately I didn't ask him why.
If it wasn't the pretensioners mounted either side of the hand brake it must have been the seat belt clips themselves? It's been way too long for me to remember now! But, yes - all of the eyelets threaded straight in. I couldn't say if that'll be the same for any other brand though.
I'm confident it'll all hold, but I try to stay slim to be on the safe side
If it wasn't the pretensioners mounted either side of the hand brake it must have been the seat belt clips themselves? It's been way too long for me to remember now! But, yes - all of the eyelets threaded straight in. I couldn't say if that'll be the same for any other brand though.
I'm confident it'll all hold, but I try to stay slim to be on the safe side
Just worked it out - those holes are for the OE seat rails, Mark must have used the harness eyelets instead of the standard bolts. These bolt right through the floor and get secured by a nut underneath, should be pretty strong.
What sort of seat subframes do you have Inferno?
What sort of seat subframes do you have Inferno?
Last edited:
Haven't got any decent pics of mine, only got one from the back.
