Mr Underhill
ClioSport Club Member
No 😂 My mate fitted my EPAS and I’ll be asking him again. Took my GoPro but couldn’t be bothered to plug it in. I’m done with all that TBH.
ClioSport.net
Register a free account today to become a member!
Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
-
When you purchase through links on our site, we may earn an affiliate commission. Read more here.
New Clio 182 Track Project
- Thread starter Mr Underhill
- Start date
SharpyClio
ClioSport Club Member
Good meet you today Jon, car was looking good. Looking forward to hopefully being on track with you 13th May!
Mr Underhill
ClioSport Club Member
I’m not attending it sadly. I’m just going to get the bits done to this car and then book a day, probably June/July. I’m working that day as well otherwise I’d have popped over 😔
Mr Underhill
ClioSport Club Member
Thanks Jon. That’s the only footage of it in the wild. Super quick car. My mates in the Megane 250 Cup said they couldn’t get near me going down that straight. Just need to sort the handling out now and grow a pair 🎱🎱
Mr Underhill
ClioSport Club Member
My 1 photo from Croft. They actually managed 4 in total, that’s how bad the red flags were. We spent more time in the garage or pit lane, than out on track.
imprezaworks
ClioSport Club Member
Mk5 Golf GTI :)
What's the engine spec again mate
Mr Underhill
ClioSport Club Member
Wossner Forged Pistons 12.8:1 (83mm)
Catcam Performance Camshafts 421s
Wossner one-piece Uprated Valve Springs
MLS Head Gasket / Seal set
Cylinder head Clean / De-coke
Hydraulic Lifter set
Head Bolt Set
Arp Con-Rod bolts
King Crankshaft Big Ends
King Crankshaft Mains
Crankshaft thrust washers
Keyway crank
Jenvey ITBs (45mm)
220.6 bhp/178 lbs ft torque
Mr Underhill
ClioSport Club Member
So much potential. Pleased with the top speed. Once I get everything else sorted it'll be a weapon.
imprezaworks
ClioSport Club Member
Mk5 Golf GTI :)
Mr Underhill
ClioSport Club Member
Very! Chicane to Tower in my last car 105 mph. This one 125 mph. Just slow everywhere else, but this was a shakedown. I know what i need to do.
Advikaz
ClioSport Club Member
Looks similar to one of the engine dynamic build sheets that. Was looking at it the other day....
Mr Underhill
ClioSport Club Member
Yes, built by Andy at ED.
Advikaz
ClioSport Club Member
Mr Underhill
ClioSport Club Member
The last owner said 920kg but I think it's heavier than that. It has got a fibreglass tailgate, the bonnet's guts are ripped out, no carpet, racing tank (20 ltrs) but full interior.
My last car was fully stripped out but had a full RO22 roll cage, plastic windows, one seat. That weighed 940 kg.
It's lighter than standard, that's for sure.
SharpyClio
ClioSport Club Member
Mine is 1020kg with half a tank so given the added lightness is defo a decent chunk less than mine!!
Mr Underhill
ClioSport Club Member
Another shot from Croft - looks faster than it was.
Lots of changes to make before getting to Croft on May 13th so I better get my finger out.
Essential things to do
Lots of changes to make before getting to Croft on May 13th so I better get my finger out.
Essential things to do
- Fit new custom Radiator, wire-up fans and controller
- Fit Roll centre correction kit
- Fit the ASTs with new springs and top mounts
- Fit the Cup air-con delete kit
- Fit new tyres
- Fit brake ducts and pipework
- Find an old laptop and get the ECU 90 software on there
- Find an EPAS set-up
Andy P
ClioSport Club Member
Clio 172, i20N
@Mr Underhill Remove the tape on the Bumper?. 
Mr Underhill
ClioSport Club Member
Just there as a precaution as there’s a bit of wear on the quick release mechanism that holds the bumper on.@Mr Underhill Remove the tape on the Bumper?.
It causes the ends of the bumper to lift slightly and whilst I’m sure it’ll hold without the tape, I don’t want to be that guy who halts a trackday session if a Marshall thinks the bumper is falling off.
I always call the TDO over to discuss anything like this before hand, so if he’s happy, I’m happy.
Unfortunately the tabs inside the arch have been removed, so it’s not like I can put a u-clip in there and a bolt to secure it. I quite like the tape to be honest because #Trackcar
SharpyClio
ClioSport Club Member
Wasn’t sure you were going on the 13th, be good to see you there
Mr Underhill
ClioSport Club Member
I’m using it as a test day so will probably be out for a few laps and back in as we set it all up. If I can get it dialled in that day I’ll be very pleased.
@Brigsy is going too
SharpyClio
ClioSport Club Member
Ah amazing! I’ll have met loads of forum folks this year!
Mr Underhill
ClioSport Club Member
A bit of a mixed day. Spent the morning putting the 172 Cup delete kit on, but all the while I kept thinking it was going to be tight with my new radiator.
I went for a fabricated Aluminium rad from Pure Motorsport. Tis a thing of beauty 😍
Began cutting out some of the metal to make it fit and damn, the pas pipe and bracket get in the way.
It’s not out by much, an inch or so.
Even if I get a custom high pressure pipe made, I’ll still need to cut a chunk out of the bracket, which isn’t an option I want to take.
Oh well, these things are sent to try us. Tools down, hot bath and a cup of tea me thinks.
Thank you for reading.
I went for a fabricated Aluminium rad from Pure Motorsport. Tis a thing of beauty 😍
Began cutting out some of the metal to make it fit and damn, the pas pipe and bracket get in the way.
It’s not out by much, an inch or so.
Even if I get a custom high pressure pipe made, I’ll still need to cut a chunk out of the bracket, which isn’t an option I want to take.
Oh well, these things are sent to try us. Tools down, hot bath and a cup of tea me thinks.
Thank you for reading.
Mr Underhill
ClioSport Club Member
Managed an hour tonight - finally no rain.
Whipped the Cup delete kit off - probably won’t be needing that now - and attached the power steering pump to the original upper bracket. Then mocked the radiator up with the Schroud.
It looks the dogs but it’s going to be tight with twin 9 inch fans and the alternator in.
A bit of gentle persuasion is going to be required 🔨 me thinks.
Nothing organised this weekend, so weather permitting, I should be able to make some progress.
Thanks for 📖
Whipped the Cup delete kit off - probably won’t be needing that now - and attached the power steering pump to the original upper bracket. Then mocked the radiator up with the Schroud.
It looks the dogs but it’s going to be tight with twin 9 inch fans and the alternator in.
A bit of gentle persuasion is going to be required 🔨 me thinks.
Nothing organised this weekend, so weather permitting, I should be able to make some progress.
Thanks for 📖
Mr Underhill
ClioSport Club Member
Another fight tonight, but I think I’ve got the better of it.
Put the other delete kit back on with new belt and moved the PAS pipes further back to allow for fans.
Next problem is getting the radiator to seat properly on the subframe.
As you can see it’s tight.
Too tight! 🖕🏻🖕🏻🖕🏻
I’ll just ream the holes a few mm and we’ll be good to go.
Last job was to plan the fan and thermostat controller wiring, so took to photoshop and mocked up a schematic.
Should all come together this weekend 🤞🏻
Put the other delete kit back on with new belt and moved the PAS pipes further back to allow for fans.
Next problem is getting the radiator to seat properly on the subframe.
As you can see it’s tight.
Too tight! 🖕🏻🖕🏻🖕🏻
I’ll just ream the holes a few mm and we’ll be good to go.
Last job was to plan the fan and thermostat controller wiring, so took to photoshop and mocked up a schematic.
Should all come together this weekend 🤞🏻
Mr Underhill
ClioSport Club Member
s**t weather again but it wasn’t going to stop me getting this radiator in.
Cut a few cms from the subframe allowing the radiator to go to the right.
This freed up the space I needed between the rad and alternator. This should be part of the installation instructions.
Lined the fans up and pushed through the cables. I put them near the top of the main structure for added support, as I noticed in the old radiator it was moving around and was loose.
One job finished.
The kit comes with bobbins which you can secure with a nut and washer - provided you’ve cut some holes in the front that is - but it seemed chewy so went for Rivnuts instead.
Cont……
Cut a few cms from the subframe allowing the radiator to go to the right.
This freed up the space I needed between the rad and alternator. This should be part of the installation instructions.
Lined the fans up and pushed through the cables. I put them near the top of the main structure for added support, as I noticed in the old radiator it was moving around and was loose.
One job finished.
The kit comes with bobbins which you can secure with a nut and washer - provided you’ve cut some holes in the front that is - but it seemed chewy so went for Rivnuts instead.
Cont……
Mr Underhill
ClioSport Club Member
With the radiator secure, I set about fitting the controller and building a loom.
Top hose off, then stuck an old rolling pin into the pipe and used the supplied cutter to punch a hole in it.
Added the screw, seal washer, then the thermostat.
Then built the loom.
Connected it all up, filled the engine with coolant, topped the power steering with redline fluid and we have fans 😍
Job done!
Tools down, hot bath and going out for a curry.
Suspension tomorrow providing the weather is kind. Thank you for reading.
Top hose off, then stuck an old rolling pin into the pipe and used the supplied cutter to punch a hole in it.
Added the screw, seal washer, then the thermostat.
Then built the loom.
Connected it all up, filled the engine with coolant, topped the power steering with redline fluid and we have fans 😍
Job done!
Tools down, hot bath and going out for a curry.
Suspension tomorrow providing the weather is kind. Thank you for reading.
Chambers_RS
ClioSport Club Member
Clio 172 Cup&Leon K1
I have that rad and have the twin spal push fans on the front which gives me enough room on the back.
Subbed to your thread aswell, car looks mega so far 👍🏻
Subbed to your thread aswell, car looks mega so far 👍🏻
Mr Underhill
ClioSport Club Member
Never thought about having them on the front 🤔 It’s not too bad now I’ve twisted and pushed the PAS pipe back a bit.
Mr Underhill
ClioSport Club Member
I’m just glad I’ve got some fans tbh Jon. I pulled back the tape from the old loom and some wires had come away, so it was never going to kick in at Croft. Glad this bits out of the way.
Mr Underhill
ClioSport Club Member
Another deluge meant the suspension switch was put on hold, and instead got lumbered with mutley until 4 o’clock.
The rain finally stopped so I made the most of the time left to put my brake ducts on.
I originally ordered the K-Tec rally ducts as they looked purposeful, but they messed me about so much I opted for some from Pure Track instead.
You can either bond or screw them in. I opted to use some M5 Rivnuts and torx screws.
It just makes life easier should I need to remove them at some point.
Whole job took an hour and I’m pleased with how they look.
I’ll add the pipe work once I’ve switched the suspension over, hopefully by next weekend.
Thank you for reading.
The rain finally stopped so I made the most of the time left to put my brake ducts on.
I originally ordered the K-Tec rally ducts as they looked purposeful, but they messed me about so much I opted for some from Pure Track instead.
You can either bond or screw them in. I opted to use some M5 Rivnuts and torx screws.
It just makes life easier should I need to remove them at some point.
Whole job took an hour and I’m pleased with how they look.
I’ll add the pipe work once I’ve switched the suspension over, hopefully by next weekend.
Thank you for reading.
Mr Underhill
ClioSport Club Member
Lighter nights and decent weather allowed me to get a few hours in after work.
Whipped the BC Racing coilovers and calipers off and disassembled the wishbones in preparation for the roll centre kit and my new suspension.
s**t photo incoming….
While everything was stripped, I had a look for leaks because after my last outing at Croft, I noticed some grease on the outer rim of my OSF wheel.
I did the taste test as I don’t want to do a @SuperJ and find out it was BBQ sauce 😂
Nothing coming from the driveshaft CV boot, but plenty on the caliper.
A closer look seemed to point to the sliders on the carriers.
Looks like it’s packed with thick grease, which also meant the sliders weren’t moving as freely as they should. I’ll give those a clean up and stick on some new rubbers, pins and brake grease.
Dug my ASTs out and switched the springs over.
I’ve opted for 90Nm front and 100Nm on the rear after chatting to lads doing the TDT/TDC championships. The springs aren’t mental money, so I can always try a few different rates if these aren’t to my liking.
Last job was temporarily fitting the top mounts.
Nice to get a few jobs out of the way mid week so I’m not spending my whole weekends fixing or prepping cars.
Thank you for reading.
Whipped the BC Racing coilovers and calipers off and disassembled the wishbones in preparation for the roll centre kit and my new suspension.
s**t photo incoming….
While everything was stripped, I had a look for leaks because after my last outing at Croft, I noticed some grease on the outer rim of my OSF wheel.
I did the taste test as I don’t want to do a @SuperJ and find out it was BBQ sauce 😂
Nothing coming from the driveshaft CV boot, but plenty on the caliper.
A closer look seemed to point to the sliders on the carriers.
Looks like it’s packed with thick grease, which also meant the sliders weren’t moving as freely as they should. I’ll give those a clean up and stick on some new rubbers, pins and brake grease.
Dug my ASTs out and switched the springs over.
I’ve opted for 90Nm front and 100Nm on the rear after chatting to lads doing the TDT/TDC championships. The springs aren’t mental money, so I can always try a few different rates if these aren’t to my liking.
Last job was temporarily fitting the top mounts.
Nice to get a few jobs out of the way mid week so I’m not spending my whole weekends fixing or prepping cars.
Thank you for reading.
