Search results

Use a resistor on the carbon canister purge valve wiring. 23 ohm rings a bell, buy one with a heatsink on from rs components.

If your not confident in doing the belts yourself, id get it to a specialist, and get them to do a report/rectify if needs be.

Just uninstall clip as normal then reinstall. The windows install will be ok.

Still reckon hes cocked up the timing. Does it sound ok when cranking? I hope a pulley has not slipped due to incorrect torquing.

Id try reinstalling it again, sometimes needs a second attempt to get it running ok. Ive stuck with 178 as works and stable.

@Touring_Rob the cartool version with red cable should be ok, i use the same cable and version 1.87, i got my cable off amazon and hoped to use a “borrowed” copy but ended up buying a licenced copy as my lead was blocked, was not too bad around £50 on ebay. Clip is great, might be worth having...

Ren0link is epic for programming keys too if you want to invest in some more software and an obdSX lead. It has an option to pull the isk/pin off the uch, super easy to do.

I use v178 and the cracked version is pretty stable. As far as i know its 32bit only.

Take it to the Renault specialist and if the timing is out id be asking the garage who done the belt for the money back. Will be able to tell on live map sensor data on clip if timing is miles out, should be around 400mbar on idle iirc. If they have not got much experience with the f4r they...

Regarding the cutting out, Id be checking the timing again if it was running ok before a belt change. Tdc sensor plug might be the cause of non start.

Changed the rack on my orange dci yesterday without dropping the subframe. Was as awful as expected undoing the bolts with a ratchet spanner:LOL:

Some more jobs done to the Kangoo Compact. Ive lost a few hours this week trying to sync the r26 ecu to the kangoo uch, initially without success and ecm immobiliser was active, resulting in short cranking and not able to delete dtc's from the ecu as immobiliser active. Information on...

Thats a toy torque wrench. Definitely invest in a bigun that will go up to 300nm or so. Failing that breaker bar, which did me proud on hub nuts for years, and is ok if you have a good feel for how tight things should be done. Got to be careful you dont go too tight though.

Buy one of these, come in handy for real stubborn trackrod ends or balljoints and quite kind on the rubber boot if you pull it down before knocking it in. Tighten it up, if it does not go straight away with a bang, hit the side of the hub and then it will go again with a bang. I have a genuine...

Eml will be a coincidence but not related. Scan it with clip and see what codes are stored.

Most likely. Torque should work with a decent obd adaptor

Should be able to read boost pressure off the obd/map sensor no problem.

Updates Both clios still soldiering on, blue one still clocking up loads of miles at work. Changed oil and filters on the blue one a couple of months back and boshed an airfilter in, old airfilter was black. Clutch started slipping shortly after on hard acceleration, so have limped it for 2...

Should be able to free the sliders off, very easy with an impact driver. I just done a set yesterday, spun them both ways until loose, removed, cleaned and greased and good as new.

Strange that it wont auto detect vin, try with ignition on. last time i installed clip im sure i just manually installed the drivers. Might need to be in administrator mode.

Drivers will work on 7. What issues are you having installing drivers? I recall plugging the cqn clip into the obd so it detected it, then installed drivers when the box pops up.

What version of windows are you using ?

Does it pick up the vin automatically? Obd port working? Try it on another Renault and make sure it works. Im sure my old one done this when it broke

Great build. First time ive seen a set of cams dialled in with a dti on a f4r, cut down cam cover is a great idea to save buying the cat cams setup.

As above needs scanning with can clip to see what faults are stored.

Cheers all. Getting there slowly First time id seen 2x valves @frayz didnt realise it was for nitrogen, good info. I initially thought the wheel had been cocked up! Good info @VenomUK Ive freed it off and well greased now. Possibly scuttle was blocked when previous owner had it. Will bleed...

A few more jobs done Kangoo clutch pipe was knacker tight so ordered a hel 250 dampener delete pipe. Had to modify the kangoo bulkhead joiner to fit the 250 pipe. Filled reservior up and stuck a pipe/syringe on the bleed point on clutch slave, pulled a vac and it bled up straight away, so...

Enjoy the economy for a couple of years, get some ncb and then buy a rs if you want more power (y)

Wrong car to be tuning for power. Enjoy the economy and cheap motoring

Done a bit more at the weekend. Mostly mocking up what will fit and finding out what needs modification. Tried a few combinations of gear cables that i have in stock, no joy as all around 75-100mm too short. Custom length bowden push pull cables are not too expensive so should be easy to sort...