Search results

Nice video @Big_Steve_T JB weld for the sump then......

Wheels back from powder coater, just couldn't bring myself to open the new in bag PH1 172 Oz centre caps so glued the 3d printed ones ready for some rattle can action tomorrow

Many thanks!

They do but too loose, after a few miles on todays roads I will have scattered 4 Renault symbols across Cambridgeshire :ROFLMAO:

Have just taken delivery of a set of 3D printed centre caps, anyone else had these from ebay 3dclever and what glue did you use to bond once sprayed? Cant get much info from seller, he states made of resin when I asked him what filament he used, couldn't confirm if PET or PLA etc just said...

Did you ever get the code?

I have used fobfix in the past, very helpful and cheap

Thank you

Hi Can anyone confirm the correct Lemforder track rod end part number, both ECP and PartsForLess list two and fitment detail info not clear? RH could be either 606745285 or 606745975 can anyone confirm from a previous order? Many thanks

Bit pricey but don't forget Musks Starlink

May help i hope, I had a 2012 250CDI and light came on at 60k.... took garage ages to find as suspected the MAF but all was okay and showed leak. They had to get a smoke machine to pressure the intake and revealed a tiny hole burnt through on the plastic inlet manifold.... this turned out to be...

You pulled and checked the relays in the fuse box by the nearside head light

Yes it will be, prob under scuttle at front not sure where on that model, quick Google should reveal for you. Likely a thread on here also just search

Failed resistor pack is a fav to fail, but normally you only lose a couple of speeds but assume all could fail... Will look like this...

Plate made me laugh on this one today

Doesn't need to be wet at bedford, who would have thought you could roll in the outward pit lane there

Had this dilemma earlier in year and went for old office carpet tiles for 50p each, hardly any wear, like new many of them, lots of places sell on ebay and two cans of spray from toolstation to stick down. Been really good so far and can jack up on them fine. Best thing has been when I spilt tin...

@Dave 200 one listed on the bay, maybe get this one refurbished https://www.ebay.co.uk/itm/184412348712 Not my listing

From memory there was a uk ebay seller boring them out to a wider diameter and re-bushing a while back, the listing used to mention corrected sticking. Just checked and cant see a listing from him on ebay and not seen for a while. Maybe someone on here knows who it was

If you have standard seats just use a bit of waste pipe 8

Reason just emailed..... A big thank you to everyone who has bought tickets and supported our company. It is with regret to announce that due to poor ticket sales the draw for the Clio 182 Trophy (and our other competitions) will not go ahead. We have worked incredibly hard over the past few...

Just got my money refunded on this one, anyone else enter? No reason given just a refund

Noticed my MPG has plummeted / dropped to 12 MPG on a steady run last two trips out and from memory only ever get down to 19 MPG on trackdays. Seems to run okay and no lights so suspect Lambda. Following forum advice, 22mm ring spanner over the connector, squirt of pen oil and got the exhaust...

@Brigsy Top tip this, worked a treat and original 20 year old lambda out in a few mins no hassle or skinned knuckles!

Can you hear pump prime and stop before you crank?

Mine did this a few weeks back was the fuel pump relay in the box by the battery. Pics of the on in my 172 thread

Its about preventing the corrosion, you wouldn't want it conducting across all the pins and shorting the loom The metal to metal makes the contact not the grease

Thank you, so that replaces the top hat and seperate nut that goes onto the shock rod first?

Some new top mount sets on the ph1 172 and found bearings solid so guess it will make it steer a little better now and fixed the sticking rear caliper, just a quick strip and clean freed it up

Intermittent starting issue resolved and new Renault relay fitted Then while at the electrics thought would sort the one and high speed heater fan it has, after a call to Renault 172 Ph1 part 7701206104 (Valeo) is now obsolete Valeo part number is 515136 and still available so one...