Search results

Just thrape the hell out of your system Get some tones on, and measure votage across amplifiers power side. WHEN ENGINE IS ON! I it drops to about 12volts you should look at uprating things. If it doesnt go below 13 its fine. Simple! Mine never drops below 12.5 volts and i run a jbl 1201.1...

Off 800wrms you shouldnt need too much of an upgrade. Yeh do TB3 and get an optima yellow top. You find these at halfrods though! and they do a size which will fit underbonnet! No need for an uprased alt, at all with that current draw!

Indeed. But you don't need friends.... everyone i know are...... associates...

Just completly sod off the passangers seat. I hate having folks in the front if there's room in the back. Only person allowed in the front of mine is the misses cus she just sits there and doesnt speak when i'm driving. She gets the same returned when she's driving!

If you really want to do it. Get it professionally done... If you're asking for help on here i don't think it should be on you consider to do yourself list. Will need a new fibreglassed centre console and something has to go to fit it in there..... Along with is there sufficient length cables...

Chris - can't afford a refurb at the moment, too busy saving up for a monitor for my ps2!! So rattle cans on the steelies it is... to get a nice black finish. Then rim them red, like couzens... but not silver ;).

Messy underwear!!!!! Thats what i like the look of. Now to pull that off on a phase 2! Those 14's mate?

How much that cost to get done though? Then new rubber needed! Can't fit into the cliosport.net stereotype i'm afraid. Make everything look like a 172/182, then turini's. Just can't be done 'fraid! Sweet so with the subs, batts and dropped by 60mm fronts and 40mm backs. Should be sweet!

CBA to pm! lol! Is that just the mad slant you're on or how much they lowered by? 60mm drop and 14" wheels with fat tyres, i like!

I suddenly like the idea even more! Those 14's or 15's?

May sound like a mad one. But lowered and on steelies please....... I'm liking the ideas at the mo, TBH!

Was Barny.... 1.2 16v stickers. Must be! Chav! lol

Power output into 2 ohm is 1114 watt rms. The units are not designed for loads under 2 ohm. So you are drawing extensive power. Say it's 85% efficient, which is optimistic for this amp. 1310 w rms is being drawn. Which at a best case scenario is 91amps (14.4volts) but at worst case (12v)...

Into what load. If it was 1 ohm then sorry mate you ragged that A6, massive voltage drop, without uprated alt to batt cabling. It's less that 8guage... across 4' which essentially powers the device during engine on operation!

I hope you have uprated engine wiring to run this amp. (alt to batt mainly) Also i believe a bad earth could be to blame. Too much resistance. thus putting the amp into protect! Check your voltage across the a,plifier terminals. Then get someone to turn it up slowly and watch the volts as it...

I was with churchill last year. 17. No previous driving or anything. £1900. Just phone around don't work on the internet. Quotes vary a lot on the phone to the net!

No iso adapter is needed for a mk2!!!! You will need the necessary adapter to use steering wheel controls however. Which i do believe that HU does not support!

Regardless of spikes or constant it's still current draw? All i'm saying is that 25mm^2 cable over any length should not be fused greater than 100amp. And that 50mm^2 can be fused at upto 250amp. I see what you're saying about it's only a burst. BUT if you fuse said wire at 200amp (to allow the...

Take a little read here... i know its for audio but the principle is exactly the same for current draw! http://www.the12volt.com/info/recwirsz.asp

Yes! Ideally over 12' you shouldnt run any more than 80 amps off 25mm^2. BUT for a shorter length 9' then it's about 100a. However 50mm^2 you're talking 250a at least over 12'. I draw a nice 180a off 25mm^2 but the cable is only 2' long. And it gets warm. Will soon be upgraded to 50mm^2 though!

Starter motor drawing too much current for that length od cable. so you should uprate the cable to 50mm^2 then fuse it at 200A

Got reg incorrect SH02CHO!!! not SHO lol!

Nah i think whats happend is plates ahve been changed. and they just stuck them on. I think the holes are there they just didn't bother to drill the new plates!!! Thanks guys, i'll drill the plates now and find soem way of fixing them on. :cool:

Re: Front bumper trim (what do i do with numberplate?) Just checked and i dont have holes fixing my plates on? They're bonded on in some funny manner? Sort of like double sided thick tape?

Ok sweet! Its only gotta get from my house to body shop ;)

Grommet is behind the glove box, whack passanger seat back, lie on back and look up. Easy to find! You wont need an iso adapter to work the HU. But you will need a set of controls for use of steering wheel's controls! Ermm... i think you need the connects 2 one...

Thanks mate. I'll try that. As long as it's visible surely its fine? :)

Ok. I've been removing trims from the clio. As taxi drivers are d1cks - See here! Rear and sides done. Just need to now how to remove the front middle one? With the number plate? And how can i stay within the law with reference to this front plate? Shall i just strap it onto the middle of the...

Sent Stourbride news some info. Have to wait and see if they publish! and pictures of said butch sister/brother will be up if you really want lol!

Oh really... and yeh chris. A white pug 406!!!