Search results

Lesson learnt then. The hard way! I'll ring around on Monday and see who can fit me in.

Especially on these stupid MK3's if they need to get to the top mount bolts! Wipers off, Scuttle panel off. At least the alignment is done! FLOL!

Haha. I don't usually like to bother people. :o I'll give places a ring then on Monday. Guessing it'll need to be booked in?

Spacers fitted, but it wasn't like that before I fitted the coilovers. LOL Scott! I know, I know. usually I wouldn't touch them with a barge pole either!

Well that's what I thought. Dammit. Looks like I'll be taking a look tomorrow then.

Where's that dude? I took it to Kwik Fit (It was the only place open!!!). :o ​

Ah, Well I asked for alignment! So they might not have touched the camber at all then? I know I should've asked for it, but it's clearly out! Surely that should be done as well?!

Fitted my coilovers today, and got them aligned. Stupidly, didn't get a printout so going back tomorrow to get one. However, just noticed my passenger side front wheel sticks out further than the driver's side!?! Passenger's side: IMAG0580 by johnpape83, on Flickr Driver's side: IMAG0581...

I can bounce the read end up and down and it won't do it. Driving though, it'll knock!

​Adjusters were set equal. I'll go double check the top of the shocks, but I did them up tight.

I've seen various threads about the MK2's, but my MK3 now with AP coilovers, is knocking at low speeds. Noise is coming from the rear. I noticed the springs for the rears are very short. The adjuster is set at halfway at present, so my ride height isn't drastically low. Untitled by...

Got lows! Coilovers fitted earlier, and alignment now done. Just need it to settle and next weekend I'll check the measurements on the height out. Won't be going much lower though than this. Maybe.... Will also be fitting my new studs and Petrol Chrome Tuner nuts. :cool: Untitled by...

Figured it out. It's both!

Hey Guys, So is it both of these that are drilled out? Anyone with a Mk3 who can help? IMAG0578 by johnpape83, on Flickr

Looks a nice example. Might need to put your photos on Photobucket/ Flickr though, as not everyone might have access to see them on Facebook.

Will see if I can make this then. Be nice to put some faces to names, and maybe see a bit of the track action.

Ok, that makes sense! Will measure up the threads and see that drop I get. I think as standard these coilovers are 30-90mm on the front, and 25-75 on the rear.

LOL! I'll be going lower dude, but not that low. I still have a steep driveway to navigate, and the roads round here are a mess. Plus I'm pretty sure slamming the shocks will shorten their life dramatically. BTW, another stupid question: When people say I've got a 60mm drop, etc. How do they...

All tightened up now. Roll on the weekend for some slamming action! :cool:

Hey Kelly. With regards to alloys, it's all about personal preference. Have a look through the threads on here though and you'll find loads of different ones! Are you planning to lower the car at all? ​Don't forget to check out http://www.cliodci.net too. :)

No, I bought genuine ones through Adam. ​Stupid MK3's have side-specific ones too. Left and Right!

See! Bloody headlights are a nightmare on these MK3's. Had to take the bumper off mine too because my massive man hands couldn't change a bulb on the passenger side.

I thought so. Thanks for clarifying James!

So I've got myself some AP's now. Top mounts arrived, and I've been putting them together. Now, stupid question time. How far down should the top mount nut go? I've tightened both sides up so there is about 5-6mm of thread showing out the top. Does it need tightening down all the way down the...

It's not a car, but with the bike, I fire it up every couple of weeks, keep it under cover (luckily I have a garage too for it), move it about to stop it being sat on the same spot on the tyres for so long (keep them pumped up too), and that's it. Battery hasn't even needed to be left on...

Nice! Sure I pass one of these in the mornings on the way to work.

Lol! I don't think I'd have the talent, just the hope that the diesel smoke emitted would blind the others and lead me to victory! (Off topic - got a text today to say delivery is tomorrow, so thanks again :) ) Might pop down to this then. It's not far at all, and considering I miss CSS this...

So different fuel pump as well? Again, I'm guessing for increased flow rate?

Cool. Just toying with ideas that will probably never come to fruition! :D A remap on the 86bhp model I've got should see it kick out about 105-110bhp, with torque going from 200nm to 240nm. Just had a quick tot-up: 2nd hand injectors: £200 a set Ultrasonic cleaning for injectors: £100 a set...

Interesting. I suspect though it wouldn't be as easy as bolting on the turbo and bigger injectors though and expecting the same output. For example, getting a 106 turbo and injectors and fitting them to the 86bhp engine.