Search results

Giving me inspiration for mine ? I fitted the Mocal catch tank to the bulk head on my cup and probably will with the Storm grey shell.

Master cylinder hoses are p clipped down now. The passenger front hose was bit of a nightmare with the straight fitting out the master not to mention being about a foot too long. To get it tidy, Miss the routing of the clutch cable and go behind the heat shielding took some patience.

Looks well smart ??

Looks awesome ?? What make fan is that? I’ve got that on my list to buy

This mine. Too much power for fwd with no diff and currently standard slipping clutch.

I like the look of the carbon reverie personally it’s what I’d buy but think as mine is pure track I’ll just run a sausage filter or no filter at all

I really want one of them boxes ?

@robzracing @vroomtshh @Nafoff Did you all have issues mounting the front hoses to the body with the little spring clip? Like @Nafoff picture here. Did you use the washers in the end like this? Mine seem really loose!

All the brake lines are ran and tightened to the calipers bar the passenger front. Need to join the caliper line to master line and then p clip them all down. Oh and make a bracket for the bias valve. Master cylinder is all in now tho.

Slow but steady progress. Radiator is in. Just needs tidying up now.

Says to use axle stands still.

Will definitely help ?? You’ve got plenty of space to slide under the sill aswell. I have to jack the back up and slide it under and turn it. I use an inpact gun to raise and lower the ramp. You had it level with all 4 wheels off the ground yet?

It was all my Milwaukee tools but has to be the tilting ramp now. For sub £400 it’s worth every penny.

So the lines are in and just need pining down now. Redrilled the rear arches in the end. As per my earlier post I ordered a new hose from Hel, order Friday PM arrived today and is spot on. Great service. Whilst ordering the hose I figured out what Proline had done to my bulk head fixings...

Nearly there with routing. Defo going to redrillthe holes lower and hope the hoses will sit better as they currently float of the floor ? I also sorted my bulk head hose as I got pretty bored.

Rear lines are done, I may have drilled the hole through the wheel arch 10/20mm to high which may effect the lines inside to the T piece. Maybe be an issue but I’ll cross that bridge later.

Beanie is just off the m1 in Milton Keynes

Airbox? Intriguing, I was looking at getting a carbon Reverie air box ? What have you got?

Decided I’m going to start from the rear of the car to fit these brake lines. Finally got some new bolts for the rear calipers to stub axle. Whilst it was too late I decide to get the drivers front hose to fitted with out rubbing and cut a little piece of metal out. Need to drill through...

Nah all straight fittings ??‍♂️

Oh make sense. It’ll look good with a centre exhaust ??

I wondered why my bias valve was back to front ??‍♂️ My ocd is telling me order another one.

That box ?

I’ve driven the same clio cup with hard lines and then with braided, and both were fine to me tbh, all personal preference. I only went this way for easy and time saving which isn’t currently working lol.

It was your set up I was copying tbf as I knew you had the grommet kit I presumed it would be a bit longer. I possibly gunna have to drill a hole in the bulk head to pass the 90 degree connector through and make a L shape bracket riveted to the bulk head, with a hole in to tighten the bulk head...

Started to look at where the brake lines will run inside the car today. It seems the lines before and after the brake bias valve are to long. Well at least one of them is to get them to run neatly. This might just be me being a bit OCD but running how I’d like the T piece is in the spare wheel...

I know JC weld fab do a fab job but couldn’t you save time and buy a PMS exhaust? Well built light and pretty quiet on the DB reader? Also I’ll be keen to know how you get on at Northampton Motorsport. I’m looking for somewhere close to map mine. Scoff at EFi has always done an amazing job but...

@robzracing where did you get the round aluminium sheet you mounted your swirl pot on?

Yeah your right. I’ve spent an hour every morning last week messing with the position. It’s fairly central yeah, loads better than the seating position in my old blue cup shell with standard rails and seat subframes. If I was to weld my own rails in I’d probably do them a tad lower tho but...

So after many hours and many different types of side mounts my seat is finally in. Needs final tightening but it’s in and out the way. Was a lot of messing about as was working around welded in seat rails suited to a different seat and my side mounts. Now that’s in I can work out where the...