Search results

On a good day about 9.8-10 for mine I recon. Chip, filter, zorst, decat, blue printed head and a few other bits.

Rally design do a 285mm brake disk for the clio £149 including caliper brackets and cross drilled disks. So another £35 for some mintex pads or what ever you like to use. And these will fit a 15" wheels I am pretty sure as the 306 gti 6 runs 285mm disks on 15" wheels.

Well the phase I had a smaller sump then the phase two and therefore two different size dip sticks. Get a phase 2 sump put on there.

You dont need dot 5 m8. Use the dot 4 castrol sin stuff just under £4 for 500ml all you need. I changed mine when I did my 16v/willy brake upgrade.

Its running lean because you are increasing the airflow to the engine. Basically if your have an induction kit and exhaust then you tend to make the car run more lean due to the air being aloud to enter and escape the engine faster. Therefore chipping will sort this.

O and to anyone who is unsure if its worth it then, I can deffinitly say yes with only a small amount of modifications to my head my car is so much better.

Yeah well you no I am Ben send us an e-mail tomorrow for the exhaust manifold. cheers mate. steve a

It is developed and looks wicked, especially with the colour coded rocker cover.

Not 100% sure but I think so yes.

Umm probably no power gain but a nice noise. However Nick at Hillpower does a sheilded induction kit with two air feeds for the 172. Looks quality. Give him a ring on 01530273633.

Yeah after owning mine for about 3 months I managed to get it set up just right. Then my car got broken into and the head unit got nicked

Hillpower induction kit is the way to go with the fog light removed for cold air feed.

Guys what do you think the 1.4 engine could take. Mines got full exhaust, decat, induction kit and fully rebuilt and slightly modified head,o,and an ecotek.(soon to be chiped). would a 35bhp jet be pushing it?

Dazman it was £20 for the springs and then £20 next month .... LOL

same thing should be ok so long as its not damaged when fitting the new pipe.

loved my old yoko 520s in the dry but they were shocking in the wet. I am looking at the new yoko 539s.

unless the sensor is on the cat then it shouldnt. the lamda sensor should be before the cat and so long as its not damaged when fitting the replacement pipe it should be fine.

Well slightly in the manner that the head was completly stripped cleaned and rebuilt. Nick took off all the major restrictions in the head and I can safely say it has made a massive improvement. As for the cam probably go for a piper cam the same Nick Hill uses. Although might opt for a 5 turbo...

I was gona say there I heard there where some places you could get it done for around £350 (again not sure where). But dont go to superchip. If Hillpower do get round to doing one then I would stick to that. should be pretty cheap as well seeing as the current chips are around £150.

already had my head slightly done by hillpower however might be thinking about a cam in the near future so i ll let you know

First things first check to see if there is enough oil in it then check for leaks etc. If these are both ok then I would have it looked at as soon as poss, as it could only be something minor and by leaving it you could make things worse. So try not to thrash it untill you have had it looked at.

The car sounds nice. I think like you said chiping is the way to go. This should work well with your other mods. And give a bit more poke

so hows the car now then with all the mods done?

quiet .... so dumb so dumb

Ring Hillpower see it they do one as its a straight through pipe and will make the car sound a bit more meaty. As lets face it the standard exhaust noise is a little quite.

I think the standard offset if around 35,36. A 60mm drop is gona require some archs mods though I would have thought on 17s

Take it to hillpower you will not find a better place for your renault.

can be due to excesive heat build up maybe due to not properly functioning cooling system.i.e. blocked etc

Anyone tried OMP disks? As they do them for my car and OMP tend to be pretty good when its comes to price and performance.

doh!!!! how do u upload the fudge packing pictures?