Search results

go and see Mick at Diamond motors he will turn the lights off with clip, I started messing around with resistors but in the end it was more hassle so got it done properly

Right so 2 for M7 and 1 for M10 from a quick look at the caliper M7 seems more like the right size.

anyone?

looking good I used WD40 for removing the glue works really well.

Done a search but found conflicting answers. Does anyone know what thread size the front and rear bleed nipples are for the 182? M7 x 1 seems about right, found these and was thinking of replacing the standard soft ones...

Cheers mate I will do some measurements before fitting just to make sure

Need a new front caliper (but thinking of doing the 2 for piece of mind) as the piston is not fully retracting so causing a slight drag, I have a 15% off voucher for GSF so looking at the calipers from them, by the time I have returned my old one and got the surcharge back I am looking at about...

sounds nice but I would make it louder

Went to Halfords today to have a look and brought the advanced cover after finding this thread it seems to fit the clio good http://www.cliosport.net/forum/showthread.php?663164-Cleaned-and-covered-ready-for-winter-cup-content

got a picture of the car covered with this one, seems reasonable price also what is the material like

not sure this is the right section. I am after a cheap indoor car cover for my track car, it is in the garage and the dust is building up on it and I have to keep walking past it, just looking for something to keep it clean and stop a big scratch appearing down the side. anyone got any...

Thanks I am not sure what that £70 would be for, it is probably just a guide price. I just sent him a photo of everything I wanted doing and asked for a price

no problem, he did a great job and was nearly half the price of others I got quotes from.

yeah I think they really suit the car got it done here http://www.floc-king.co.uk/contacts.shtml

I have had a set of Cooksport springs for a while but finally fitted them the other day along with new front shocks (will replace the rear shocks later on) and also fitted the PMS strut brace and top mounts, it is sitting so much better now just need to fit the camber bolts and get the geo set...

Thanks Kev, I was getting mixed up with the rear

if it is just a dowty washer any hydraulic suppliers will have them if you know the size

I have some 15 inch pro race 1.2 et43 with 205/50/15 Federal RSR's, I am keeping standard cup shocks but putting cooksport springs on. ATM with standard springs I have between 12-15mm (measured with a fat finger lol) between the tyre and the strut. I am looking to run around 2.25deg of negative...

Got the PMS gear linkage fitted, got Mick at Diamond motors to do it as I could not be arsed lying on the floor in winter, and it has transformed the car and I can now reach 1st and reverse easily when I am strapped into the seat

Just a track car for fun, racing would be good but too expensive

I have some cooksports waiting just need time to do it as I have the PMS strut brace and solid top mounts to do as well.

Thanks for the comments yeah I fitted it myself, was not that bad just a lot of taking in and out

heres mine but it has not been used yet still in the build process

I got the car in October and a week after that the work started, including lots of phone calls ordering bits.:D list so far is Safety Devices 6 point bolt in cage Bimarco Futura bucket seats Bimarco Aluminium side mounts Pair of 6 point Sabelt harnesses Oreca 330mm steering wheel Flocked...

not me but I think I looked at that thread a load of times and thought changing buttons is too much messing about, as I was not 100% confident in what I would be doing.

jigsaw with a very fine blade and then just used a file to tidy it up.

the horn is on a ph1 indicator stalk. the carbon plate is just one off ebay and I cut it to the shape I wanted http://www.ebay.co.uk/itm/261188073642?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649

I have my ph1 indicator stalk and MOMO boss on my 182 but it is not self cancelling, is there something that needs to be done to it to make it work?

I am not brilliant with electrics so decided on another way for attaching the cruise buttons without taking them apart.

lol I would give him a call as he is doing another top steering cowl cover for me as I broke the clip that holds it down when fitting it :o and he said he is very busy at the moment so you may have to plan it a good few weeks in advance.