Search results

Ah right ok. Well it would be a shame to see the cup get broken mate, but needs must I suppose! Shame you can't just shelve it and put it on the back burner.

How come mate?

What's the fronts pulling?

Thanks for taking the time to read it all mate! And thanks for the kind words.

DC16 V8 is where it's at mate. They're torque restricted up until 10th or 11th gear to protect the box iirc! Lol! Only the 730hp variant though.

Yes mate. It's a Scania DC13 XPI. Common rail fuel injection, egr and VGT. Runs about 3-4 bar of boost under full load.

Hi Gerben. The grey ones are used for the reverse shaft, 1st and 2nd selector and 3rd and 4th selector. The black one is used in the 5th gear shaft. God knows why because they're all the f**king same! Lol! Little tip - get some 12mm bolts to hold the spring and ball bearings in place for 1/2 &...

Yeah it is on the big side. Lol! The engine there in that state weighs in at around a ton Martin. That's without oil and coolant! It's been in for a full strip down and overhaul as the ceramic plungers in the high pressure fuel pump disintegrated and decided to spread the love throughout the...

Looking good buddy!

Yeah get them sent over mate! Interested to see those pics for sure.

No problem at all. Any stress, give me a nudge.

Ah mate! Genuine mountune rs2k engine!! You never said you had one of those!!

Yeah apologies, I should've known that as I've helped another member with wiring a tps sensor in on a ph2 only the other day! Just replicate the wiring for the ph1 on the ph2 loom mate, but make sure you remove the remaining pins mate. It's then just a case of connecting 48, 74 and 75 into the...

@Doogimus the 6 wires that go into the ecu plug on your current loom need to be removed from your ecu plug. 3 of them need to then be transferred to the pins you stated above. It doesn't matter which 3, just remember the colours. Cut the 6 pin plug off and fold back the 3 wires your not going...

Have you machined the calipers to work with the 280 brackets? I'm going to hazard a guess that you haven't.

RWD conversion for through the winter! Just a case of slotting this 13ltr, 440hp motor in. Might need to up the front Spring rates to accommodate the slight increase in weight over the front end though. Lol!

The startup map will be a 197 map mate that's written for the gen90. That'll give some base settings just to get it to run, then it's a case of doing a bit of road mapping to make sure it's not running rich/lean. I'll do the driving and Chip will be doing the road mapping. That will then allow...

I do TF mate. I like being mixed in with the bikes and people just having a steady drive round! Lol! Makes it more of a challenge to get a decent lap time in, as you have to constantly be on your toes and work out where your going to catch, then overtake them with minimal effect on the lap...

I think you'll struggle to get 290's under 15's mate. Most people use the original 280's for 15's and 300mm scenic discs for 16's.

You need the correct tools mate, yes. You can't buy the Grp n tools either. Mine was a custom made job.

Unfortunately it's not that easy @Chambers_RS! Lol

Your going to need all the tools mate to do the job properly. Once the timing is correct, you have to lock the cam pulleys and tighten everything up to the correct torque. Once you've done that, you need to turn the engine over again and recheck/adjust if it's still out.

@Chambers_RS have you got all the locking tools as well? You'll need them to loosen off the pulleys. I've done a few where they don't lose the timing from gunning the bottom pulley bolt off. The locking pin location is easy to get wrong, but you'll know when it's in the right place. If you can...

Are you replacing the belt at the same time? Or just adjusting the timing?

Lol! Best way!! Solder sleeves as well - don't forget them!!

I might be at the 'ring at the same time as you then next year! Lol! Buy one of the pre made fuse/relay boxes and make the in-car loom yourself. You only need basic tools and an understanding of electrics. Engine loom is the same, but you need fancy crimp pliers to do the ecu terminals. You...

That's what the lads I work with think as well! They're supposedly trained up to do electrics as well! Thanks bud.

Yes to all mate! Lol

Well the wires you can see just need tidying up with rayon loom tape mate. Cutting the wrong wires can lead to all sorts of dramas, so any things possible with French electrics!!! Nah you'll not need a new ecu for the engine and interior mate. Ecu will control the engine and any comms from the...

:spanner::spanner::spanner::spanner::spanner: Got plenty more. Lol!