Search results

I have been thinking about changing my standard HU in my 200 cup to an after market one. Its been some time since I did any audio upgrades to a car, so: Will I need any kits for the steering controls (volume ones on steering wheel)? Will the new HU work with the dash display, can you can...

Cheers mate, i'll get the parents to give him a call.

Hi, Does anyone know of any good dent removal specialists in the Birmingham area? My parents are selling a car an want to take some small dents out of it before selling etc. Cheers.

My mate wants to get his wheels sprayed the same athracite as that on my 200 cup, does anyone know the Renualt colour code for the anthracite for the standard 200 cup wheels? Thank you.

Love it, stunning example!

Does anyone know of any good touch up paint for red brembos? I ask it seems of have a few small stone chips on the passenger side calipers and wanted to touch them up with some good colour matched paint. Cheers.

Cheers Tom, yeah just and went to have a look, they even have little icons lol

You know whats next lol....how do you remove the horn fuse, pull out the relevant fuse from the fuse tray @ low level? I need to make sure i get the right one as i dont want the airbag going off lol. Cheers.

I presume I will need to disconnect battery too? This bolt you mention, is it a special bolt or will any bolt do? If special, i'll order a few from you. Cheers.

I need to get access to the indicator switches and I know the steering wheel needs to come off. How do I do this, is it an easy job? Thanks.

No doesnt seem to happen when reving high. Yeah tried adjusting the steering column as well. Its probably something simple, but just wanted to ask if anyone else had it and resolved it.

Ok I know its French and I can take most rattles etc, but this one is getting annoying. There seems to be a vibrating/buzzing noise around steering column when going over slightly rougher tarmac, only started recently. Sound like something is loose and then vibrates when the shock from...

Cheers people for all your replies etc, I think i'll take a look over at 197 at that guide.

Only going on what I have read lol, is that the wrong way to go?

I dont have a grinder lol, can it be done manually by sanding? Do you mean chamfering the edges etc? I'll be using lots of copper slip as well me thinks! Whats the best method to knock the 2 pins out? Use a hammer and something to knock the heads of the pins I presume?

Fred@BTM, I assume the fix is as per aldo_87's comments? In otherwords I need to get the pads out and clean up etc?

I have a 200 cup and the brembos have been squeeling under moderate braking. Renault Birmingham dont seem to want to know for warranty work and say its not covered for that even though the car has only done 4000miles?! So I am thinking I may need to strip down the brakes and give them a...

I am based in Solihull (near Birmingham), so if anyone is near or thereabouts I could pop down etc.

Hi, I recently had some fog lights fitted to my 200 cup. All the relevant parts were fitted to the wiring that was already there inside the bumper and I had a new switch fitted (with the front fog light option). Only problem is they just dont work?! The garage said they have checked...

I have recently had some fog lights fitted on my 200 cup (not FF) and I have had all the correct parts fitted etc including a new switch with fog light option. All of the wiring was already there (minus the loom to connect each fog light). However the lights just wont work, so I have come to...

Cheers gents, I have a feeling the bumper hasnt been fitted back on right or something, either way its going to get sorted as it looks stupid

Cheers Harpham, if you could possible have a close look between the gap of the headlight and bumper to see what the fixings actually are that would be great. Thanks.

Could anyone with a 200 cup possibly have a look for me please? I wanto to try to get to the bottom of this before the car goes back. Cheers.

Yeah you cant see it on yours, possibly because of the black surround. I think they have put the bumper on wrong or something, d*ckheads lol although i'd still have thought that Renualt would use black fixings?

Yeah I should have mentioned its the same both sides, it just looks wrong lol, surely this cant be right?

Had a local garage take my front bumper off as I am looking at getting some fog lamps fitted, anyway the car came back and i noticed 2 pop rivet fixings showing through the headlight where the black bumper insert fixes to the bumper. I dont recall seeing pop rivets before, which makes me think...

There was an option if I recall for privacy tints (rear side and tailgate). Does anyone know what % the tints are as factory standard? Cant be more than less than say 35% light transmission (clear being 70%?) can it? I ask as I am thinking of having it done to my 200 cup. Thanks.

Fair play, I think it finishes off the car well

Hey lovely car, I see you went the colour coded side strips and wing mirrors, I decided to do the same when i got mine.

Gorgeous colour, one of my favourite colours.