bearing

Would like some advice on what you guys think this could be.... Basically when I'm driving theres a loud whurring noise, like a knackered wheel bearing, gets very loud at speeds over 40/50mph with the noise still being there when rolling in neutral, and tbh sounds like its coming from the rear...

Hi Guys, got a weird noise on my 182 cup, feels like a brake disk being rubbed as its a rotational noise, anyone ever had this? also, think my driveshaft might be on its way out too. Had a knocking noise when stationary when moving the wheel from side to side. Also makes a weird noise when...

right, had bit of a mare snapping a bolt in rear axel, sooo while getting it fixed they found my rear wheel to be whobbling, they checked it and we found bearing bolt was lose, we got it tightned and was mintafter, my fear is what locks this in place. can it just undo again it was a fair way off...

I think my clutch release bearing is going knackered as there is a noise when I dip my clutch, I have been told just to leave it and it's not worth doing, and its just because of the cold weather,but what will happen if it goes completely? Will it cause alot of damage and how much is it to fix?

:mad: HELP Ave had a really annoying noise coming from the back end of my car.... It sounds like fooked wheel bearings! I have just had my discs and pads done so the back bearings were replaced then, PROBLEM the irritating noise is still there.... Gets louder when I slow down.... People have...

just had rear wheel bearing done and garage charged me £96.thought that was a bit to much

After a month or so of trying to find out where the noise from the engine bay was coming from i got a second opinion from a fellow Clio Sport enthusiast. Reckons its my altinator bearings. Need some advice on how to fix this problem? Can i just change the bearings? Is a new altinator needed...

The software I have for parts (not renault) is showing me two options for the fr wheel bearing on my 172 cup. One is a 72mm diameter, the other is an 84mm diameter. Anyone know which is the correct size?

Mr Faulks will soon be fitting some spherical bearings to my front wishbones and rear-beam, anyone else fitted these? Happy with them? Any cons?

probably a stupid question, is the release bearing within the clutch, im replacing the gearbox and the clutch with a new clutch and a refurbed gearbox and just wondering if would also need to replace the bearing aswell or if it comes within the clutch kit, cheers liam

Has anyone fitted these yet? im 95% sure im going to get a set but my only concern is do they knock atall over heavy bumps? My original ones are knackered and I dont really want to replace them with something that makes as much noise as the original rubber pieces of tripe!! Have seen very good...

i'm after some wheel bearings but which do i go for? genuine renault or others? what are good what are not?

hey ppl pretty sure its a bearing problem as i have had car up in air and plenty of play with the wheel but no noise! other times with bearings i have alot of noise is there anything else this could be? also when play with wheel brake disc also moves and also behind the wheel drive shaft looks...

simple question (hopefully!) When someone says it comes as a "whole kit" rather than just a new bearing what does that "whole kit" actually include? I was told it's about £80+vat if that helps. One needs doing but trying to decide if it's worth getting them both done at the same time...

I can't find an uprated Clutch Release Bearing anywhere for the 1.6 Clio, or the 172 etc. So, on my Super1600 car have been using a standard bearing with a padel clutch and dog box. What is happening is the release bearing is cracking with use, since its only plastic. Does anyone know of an...

Any good? Renault are £65 but these are OE spec with the nut and cir clip for £35? http://www.k-tecracing.com/show_product.asp?id=2318&appid=2

that s gone dead yesterday, likely I was 5 minutes away from my place. there s loads of play in the while and it sounds horrible, i think the wheel s clipping the arch liner! Bottom line, im going to the nearest garage and i dont really want to get ripped off.......he said it will probably needs...

Ok, I know one of my front ones has had it, but the question is, which one do I require. As there appears to be two different sizes, the cars a 2004 ph3 1.6 if it changes anything...

After confusion on which bearing and sourcing a new bearing and fitting into the hub, just a question. Theres circlip grooves on both sides of the bearing but im sure there was only one circlip on the inside and the other (wheel side) not fitted ? Plus its a magnetic one, guess its ABS related...

Hey, It's not happened to me before so can't be sure but I think my clutch bearing might be on it's last legs. (51 plate Phase 2) I'm getting a loud whine when I start it from cold which changes tone when I dip the clutch. It goes away after 5 mins when the engine's up to normal temp. Noise...

Dimension is 40x86x40 in the manual, is that a 182 Cup one ?

...well that's what it feels like at the mo! Bought some cheap rear discs with bearings already pressed in. Bad idea, the bearing lasted two hours on track. Who ever coined the phrase 'buy cheap, buy twice' was spot on. So after reading a few threads on here I took myself to Renault to buy a...

all of a sudden im getting a funny noise from my rear passenger wheel bearing anyone know whr the cheap place would be for a replacement?

Does anybody know anywhere or anyone who can machine a bearing or a component for a bearing ? This is what i need made , or very similar, the centre is part of the bearing. any help or contact numbers would be great. And yes tried some companies , google etc but not much luck.

Right just wanted to make sure I'm going to be buying the right ones, if I fit megane 225 rods into a f4r with f4r crank can I just buy f4r big end bearings/shells? Also where is the best place to buy head bolts, head gasket set, big end bearings and piston rings set

Hopefully this will prevent a disaster for someone... As most will know, the rear bearings on the 1*2 is insude the rear disk, this means they are essentially changed every time you fit new disks (those that are supplied with bearings). I changed the rear bearings a few months ago, which is a...

hi folks I've bought some new rear discs and pads for my 172 Cup, the discs came with bearings but they're not pressed in to the discs :dapprove: this is the discs... these are the bearings... First of all, which way round do the bearings go in to the discs? do i insert the end of the...

hi all i have read through a fair few threads but still have not got the answer needed. i have a droning front bearing, now i have sourced a brand new genuine renault one off a friend,only problem is i have read that the 182 has different front bearings to the 182 cup/trophy??? i have a...

has anyone had any issues with wheel bearings wearing out etc after fitting spacers? mechanic i was talking to said it can cause them to mess up/wear out fast etc

Alright guys.... Having abit of an issue with my rear passenger side wheel bearing. After replacing them 5months or so ago (disks aswell) the passenger side one has gone already for sum unknown reason? Anyways....when my mechanic went to replace the disk....he found a small washer in behind...