Search results

oh just one more question, any idea what the pressures should be? At the mo im running 32 all round as a safe bet til i find out the exact pressures. Thanks Dazz

well just got my set off mark fisher. Seems like a nice bloke with a bluddy ace car!!! Just fitted them, off with the mud flaps, and work superb. Think the speedo under reads slightly but it handles lovely :) BTW, what does the offset effect? also, BenR are u sure there wont be a slight...

Just another question. Will phase 2 16v alloys have much effect on my speedo? i.e. will it over or under read? Also, are there any other downfalls except loss of acceleration? And finally will improve handling much over the standard steelies? Thanks Dazz

oh when the weather dries up a bit over the next couple of days il take a look. If its not the discs what else is it likely to be? Thanks

ah damn. thanks ben

Is the offset for an RT 36? or is it something difference. I;m looking at a set of alloys of the following spec: 4x108 stud fitment, the off set is ET/40. The tires are 195x50x15. Doest anyone know if these will fit or not? Thanks Darren

Hi all Ever since ive had my rt its always made a rubbing noise from the front left wheel when reversing to the left, this wasnt a huge prob and i got used to it. Now, whenever i reverse to the right sometimes the whole car will judder, its hard to tell what wheel its coming from as its quite...

or get a replacement filter and do a DIY cold air feed, prolly just as effective and under half the price. PM me if u want more info

does it work on phase 3? or not at all? when i got mine it didnt work on 1 or 2, turned out the resistor needed replacing hth dazz

well on mine it is, u basically stick ur head under the front of the car, ull see the sump, and a cover which moves slightly. This is the gear box cover thats supposed to protect the linkage. If u cant see it look for a silver bar running up the middle of the car (no the exhaust :-p) then...

yeah pretty much, it definitely makes a noticeable difference, especially in the lower gears. Il cut the plastic flap off eventually, im just testing it at the moment to make sure i dont cause any probs. So far, so good :)

yeah it aint as hard as it sounds. ive done it on mine a couple of time to change the bulbs. If you dont take your CD player be careful when you pull the unit out that the cables arent caught and get damaged. Apart from that its just a case of unscrewing and removing the whole unit. The heater...

I was under the motor this morning cleaning up the some and gear shield, and noticed the gear linkage at the bottom of the gear box was really sh*tty, oily and dirty. Is there anyway of cleaning this up? I dare use WD40 as itll knock all the oil and grease off. Any ideas? Thanks Dazz

Hi all After getting a piperx element for me rt i decided to make a cold air feed. I didnt have much luck tracking down any ducting so decided to have a go with the existing one. Firstly i detached the end from the tube that goes into the wheel arch. I then unclipped the flap that directs...

brill thanks :) does that mean i get 2 stars hehe :)

Here we go, all resized :) http://www.wellbored.com/clioresized.gif

nah im not a member :-( only had my clio for about 2 months so havent got round to it yet :) Il get that done asap.

never heard of it?

Hi Im after some ducting for my clio. I wanna run a cold air feed to the air box instead of the existing one that goes into the wheel arch. Ive tried homebase and B+Q but they have naff all. Anyone else have any recommendations? i dont wanna go to halfords and pay £20 for a piece of pipe...

Hi all Ive got a very slight oil leak on my car. Its no that bad as it doesnt drip at all, its just the bottom of the engine is really covered. I was wondering if this could be related to having problems getting into 1st and 2nd gear? I heard it could be oil leaking onto the clutch plates from...

all done now, see previous posts, the banner should be updated :)

okey dokey, il have it done in a jiffy (need a shower 1st - hard days work and all that malarky) :)

can always get a replacement element, doesnt effect insurance and will do a similar job. Just got one for my RT, definitely made a difference. 0-60s have come down from around 11.5 to 11.1. This isnt just a one-off as i do this sort of thing 3 or 4 times a week so know for sure when a mod...

where from? i had a look at k-tec but theyre looking for around £100 for just pads, and another £100 for discs?

wheres the best place to get the discs and pads, and how much am i looking at spending? Thanks

Would 16v brakes fit a phase I RT? If so are they hard to fit? Thanks :) Also, would it be ok to just upgrade the front brakes to 16v and leave the backs as they are or should the whole lot be done? Thanks Dazz

steve_rt, did this actually solve the problem as ive had a lumpy idle on mine since ive had it. Thanks Dazz

depends on whos u think is best :) i can have another go hehehe :) ;)

:D

Ok, heres my attempt :) http://www.wellbored.com/clio.gif Wadda us reckon? only 12kb as well :)