Search results

safety devices do a nice one, and not that expensive either. around £150 for the rear!

ull be lucky to get 20bhp from the mods mentioned, unless u have internal mods. Also some rolling roads are low reading, as some are high! What was the @wheels figure, and torque?

lol

Bondy can get u legit Kent cams and verniers cheap! PM him! top bloke!!!!

ah uv got cams, chip already! u could get the 2.0 bottom end on it then, or have ur lightened and balanced, and get it revving to 8k hehe! Lightened flywheel wouldnt make that much a difference, as its already pretty light, i was gonna have mine done, and the bloke said not to bother as its...

Not sure about 30bhp. Standard willy lump is 150. 13bhp up on the valver lump! As for tuning the 1.8 lump, iv done it, and i am happy, but it would have been a bit cheaper and easier to go for the straight swap with the willy lump. Mine is about as fast as a standard willy, maybe a...

Gone up to £225 now? Whats the difference?

TBH unless u got some mods on it, and u pay the extra getting it unichipped i wouldnt bother with the chip. I had one after i had cams etc fitted, and it did nothing apart from raise the reve limit. and at the time my peak power was just under 7k anyway so no need to rev any further! Cost for...

u gonna go to pod for a test 1/4 mile mate?

dont put it in a 5 though lol

yeah, if ur speedo cable bust then thats the reason! it senses when ur moving so to keep the revs up longer when you put the clutch in to change gear!

pull them off by sliding them forward (i think) if not try backwards, if they dont come off pull them, as u need new clips anyway as they are different. Twist the plastic cips out, the get to renault and buy some phase 2 clips, twist them in then stide the new bump strips on. jobs a good un!

Mines like this too, gonna have a look at it today i reckon!

sh1te didnt realise it was a week today! so whos going?

they charge that to do headwork, but usually you give them a head and £300ish and they give it u back! Then ull have the labour on top to remove the head and re- fit it with new head gasket! prob another couple of hundred or so!

his valvers been to Hill Power for some bits :confused:

That is how many there are, aint it?

should have slapped him, and said "act like a b**ch, slapped like a b**ch"

yeah they are set to kent instructions, and it runs spot on. Just wondered if there may be a few horsies hiding in there than could be released! What would the guy do on the RR to set it up then? bearing in mind he wont be touching the ECU. Just adjust fuelling using the PBV? Cheers

When i had cams and verniers fitted they were setup to Kent manufactured recommendaion. Is it worth getting them timed as best they can be? and would i need to take itto the RR? I rang a guy before I had the work done, and he said he could set the car up for me once the engine was built...

ah right! ok, cheers! i reckon tom_16v has 15.2 as well! See what happens on 25th. u lot going?

out of interest whats the quickest 1.8 valver 1/4 mile time by anyone on here? You 2.0s can bugger off hehe! Didnt Nick Read get 14.8? but on nos? Craig.

exactly! so it costs u loads more in insurance, and u may be saving your own life if u have an accident! I can see what they are saying with people who want them must be driving pretty quick to even consider rolling, but still.........

who u with night icon? and reason for getting one would be this for one! Matt Cony from the PGAC forum rolled his 205 Turbo and would be dead without it. I Should be Dead - but live to tell the tale ! Well all I can say is I’m 1 lucky chap to be even typing this story up, let...

i wouldnt bother attempting to port and polish a head urself if u dont know how! its not as simple as mentioned above! BenR will tell u all u need to know!

might have swapped steerign wheel over. lot of people prefer phase 1 as its a bit thicker!

how did it affect ur insurance? iv heard it can double it :o

ok i might try to get one tomorrow. iv got a 19 inlet somewhere might see if thats got one on it! Cheers!

no i dont think it has! Where are the £60 ones from mate? Cheers

That reminds me iv had one in teh garage about 3 months! might fit that bugger tomorrow!